999-995-411.10_REV A
Pipe Patch Specifications
Pipe patch kits are available for a variety of inner pipe di-
ameters in various lengths.
Refer to the RIDGID catalog
for specific offerings.
Patch Material ..............Fiberglass
Resin Type ...................Two-Component Organic Silicate
Mineral
Resin Mix
Ratio .............................2:1 by volume, Controlled by
Containers. Make sure both con-
tainers are marked the same (32"
or 3')
Resin Shelf Life ............One Year, Use By Date On
Carton/Resin Container
Resin Storage
Temperature .................41°F to 113°F (5°C to 45°C) Do
not allow resin to freeze
Resin Application
Temperature ................41°F to 68° F (5°C to 20°C)
Working Time
(Pot Life) .......................15 Minutes (At Resin Application
Temperature)
Resin Set Time ............90 Minutes (Internal Pipe Tem-
perature 50F° to 68°F (10°C to
20°C))
180 Minutes (Internal Pipe Tem-
perature 41°F to 49°F (5° to 9°C))
5
Pipe Patch
Specifications
Pipe Patch Installation Equipment
Packer/
Nominal
Pipe Ø
Overall
Packer
Length
Max.
Patch
Length
Minimum
Encroachment
Zone**
Packer
Operating
Pressure*
22°, 45°,
Long
Radius 90°
Elbows
Short
Radius 90°
Elbows
and P-Trap
Pipe Size
Transitions
Air Push
Rods
Resin
Amount
Resin
Wet Out
Pipe Patch
Elastic
Bands
2"
43"
32"
3"
43 psi
Y
Y
N
10'
Integral
32"
Off
Packer
2"
3"
43"
32"
3"
60 psi
Y
Y
N
5'
Sections
32"
On
Packer
3" - 6"
3" - 4"
4'
36"
5"
50 psi
Y
4" Only
3" - 4"
5'
Sections
3'
On
Packer
3" - 6"
3" - 4"
7'
68"
5"
50 psi
Y
4" Only
3" - 4"
5'
Sections
2 x 3'
On
Packer
3" - 6"
4" - 6"
4'
36"
5"
36 psi
Y
6" Only
4" - 6"
5'
Sections
3'
Off
Packer
3" - 6"
4" - 6"
7'
68"
5"
36 psi
Y
6" Only
4" - 6"
5'
Sections
2 x 3'
Off
Packer
3" - 6"
* Do not exceed packer operating pressure
** Minimum amount of exposed packer rubber at end of patch required for proper installation of patch.
Air Push Rod (For use with 3" and larger packers)
Nominal
Length ........................5' (1.5 m) each
Maximum
Reach .........................100' (30.5 m)
Maximum
Pressure .....................217 PSI (15 Bar)
Not for use through P-traps or 3" elbows
Air Hose Length ...........100’ (30.5 m)
Pneumatic Connector
Type ..............................Locking
Adapter .........................Adapts standard air hose con-
nectors to locking style used with
RIDGID pipe patching equipment
Required Compressed Air
Supply ..........................100 psi to 130 psi (6.9 to 9.0 Bar)
Pull Rope ......................750 pound (3.3 kN) rating,
¼" (6.4mm) Diameter, 250’ (76 m)
Long
Gloves ..........................Nitrile
2" RIDGID Pipe Patch
Elastic Bands ...............Specially sized for use with
RIDGID 2" packer
3" - 6" RIDGID Pipe Patch
Elastic Bands ...............Specially sized for use with
RIDGID 3" to 6" packers
www.
.com
1.800.561.8187