background image

21

Pipe Patch

 999-995-411.10_REV A

  6.  Wait for 5 minutes and check the air pressure. If the 

pressure has dropped, there is a leak, do not use the 
packer until the leak is fixed. Leaks in the connections 
may be able to be fixed by tightening connections or 
lubricating seals. If the packer itself is leaking, it can 
be sent for service.

  7.  After the test is complete, depressurize the system 

and disassemble.

Service And Repair

 WARNING

Improper service or repair can make machine 

unsafe to operate.

Service and repair on the Pipe Patching system must be 
performed by a RIDGID Authorized Independent Service 
Center. Use only RIDGID service parts.

For information on your nearest RIDGID Authorized Inde- 
pendent Service Center or any service or repair ques-
tions, 

see Contact Information

 section in this manual.

Optional Equipment

 WARNING

To reduce the risk of serious injury, only use acces-

sories specifically designed and recommended for 

use with the RIDGID Pipe Patching System, such as 

those listed below.

Disposal

Parts of this equipment contain valuable materials and 
can be recycled. There are companies that specialize in 
recycling that may be found locally. Dispose of the com-
ponents in compliance with all applicable regulations. 
Contact your local waste management authority for more 
information. 

Catalog

No.

Description

74658

Pipe Patch Starter System - 2" Pipe x 32" Repair

74663

Pipe Patch Starter System - 3" Pipe x 32" Repair

74673

Pipe Patch Starter System - 3-4" Pipe x 3' Repair 

74683

Pipe Patch Starter System - 4-6" Pipe x 3' Repair

74693

Pipe Patch Kit - 2" Pipe x 32" Repair

74698

Pipe Patch Kit - 3" Pipe x 32" Repair

74703

Pipe Patch Kit - 3-4" Pipe x 3' Repair

74708

Pipe Patch Kit - 3-4" Pipe x 6' Repair

74713

Pipe Patch Kit - 4-6" Pipe x 3' Repair

74718

Pipe Patch Kit - 4-6" Pipe x 6' Repair

74723

Pipe Patch Containment Kit for 2" Packer

74728

Pipe Patch Containment Kit for 3" Packer

74733

Pipe Patch Containment Kit for 3-4" Packer

74738

Pipe Patch Containment Kit for 4-6" Packer

74743

Pipe Patch Packer - 2" Pipe x 43" Length

74748

Pipe Patch Packer - 3" Pipe x 43" Length

74753

Pipe Patch Packer - 3-4" Pipe x 4' Length

74758

Pipe Patch Packer - 3-4" Pipe x 7' Length

74763

Pipe Patch Packer - 4-6" Pipe x 4' Length

74768

Pipe Patch Packer - 4-6" Pipe x 7' Length

74773

Pipe Patch Air Push Rod - 5' Length

Catalog

No.

Description

74783

Pipe Patch Air Regulator

74798

Pipe Patch Ball & Spring Leader Guide for 3-4" & 4-6" Packers

74803

Pipe Patch 2" Ball Guide for 3-4" & 4-6" Packers

74808

Pipe Patch Flexible Adapter - 3-4" Packers

74813

Pipe Patch Flexible Adapter - 3" & 4-6" Packers

74818

Pipe Patch Standard to Lockable Air Adapter 

74823

Pipe Patch Pull Rope - 250' Length

74828

Pipe Patch 100' Air Hose - Fittings Included

74838

Pipe Patch 1/4" Steinco F/F Lockable Coupling

74848

Pipe Patch “D” Ring for 3-4" & 4-6" Packers

74873

Pipe Patch Quick Links (Qty-2)

74863

Pipe Patch Resin Only - 3' Patch

74878

Pipe Patch Resin Only - 32" Patch

74858

Pipe Patch Elastic Bands for 3", 3-4" & 4-6" Packers

74853

Pipe Patch Carry Bag

74868

Pipe Patch Tape

75358

Pipe Patch Elastic Bands for 2" Packers

75368

Pipe Patch “D” Ring for 2" & 3" Packers

74883

Pipe Patch Air Gauge

74888

Pipe Patch Ball & Spring Leader Guide for 2" & 3" Packers

74893

Pipe Patch 2" Ball Guide for 2" & 3" Packers

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for Pipe Patch

























Reviews: