background image

3 – English

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions.

 Failure 

to follow all instructions listed below may result 
in electric shock, fire, and/or serious personal 
injury.

SAVE THESE INSTRUCTIONS

WORK AREA

 

Keep your work area clean and well lit. 

Cluttered 

benches and dark areas invite accidents. Floor must not 
be slippery from wax or dust.

 

Do not operate air compressors in explosive atmo-
spheres, such as in the presence of flammable liquids, 
gases, or dust.

 Power tools create sparks which may 

ignite the dust or fumes.

 

Keep bystanders, children, and visitors away while 
operating an air compressor. 

Distractions can cause you 

to lose control.

 

Operate air compressor in an open area at least 18 in. 
away from any wall or object that could restrict the 
flow of fresh air to ventilation openings.

ELECTRICAL SAFETY

 

Avoid body contact with grounded surfaces such as 
pipes, radiators, ranges, and refrigerators. 

There is an 

increased risk of electric shock if your body is grounded.

 

Don’t expose air compressors to rain or wet condi-
tions. 

Water entering an air compressor will increase the 

risk of electric shock.

 

Do not abuse the cord. Never use the cord to carry 
the air compressor or pull the plug from an outlet. 
Keep cord away from heat, oil, sharp edges, or moving 
parts. Replace damaged cords immediately. 

Damaged 

cords increase the risk of electric shock.

 

When operating an air compressor outside, use an out-
door extension cord marked “W-A” or “W”. 

These cords 

are rated for outdoor use and reduce the risk of electric shock.

PERSONAL SAFETY

 

Always wear eye protection with side shields marked 
to comply with ANSI Z87.1 as well as hearing protec-
tion when operating this equipment.

 

The employer and/or user must ensure that proper 
eye protection is worn. 

We recommend a Wide Vision 

Safety Mask for use over eyeglasses or standard safety 
glasses that provide protection against flying particles 
both from the front and side. Always use eye protection 
which is marked to comply with ANSI Z87.1.

 

Additional safety protection will be required in some 
environments. 

For example, the working area may 

include exposure to a noise level which can lead to hear-
ing damage. The employer and user must ensure that any 

necessary hearing protection is provided and used by the 
operator and others in the work area. Some environments 
will require the use of head protection equipment. When 
required, the employer and user must ensure that head 
protection marked to comply with ANSI Z89.1 is used.

 

Stay alert, watch what you are doing, and use com-
mon sense when operating the air compressor. Do 
not use product while tired or under the influence of 
drugs, alcohol, or medication. 

A moment of inattention 

while operating an air compressor may result in serious 
personal injury.

 

Dress properly. Do not wear loose clothing or jewelry. 
Contain long hair. Keep your hair, clothing, and gloves 
away from moving parts. 

Loose clothes, jewelry, or long 

hair can be caught in moving parts.

 

Do not overreach. Keep proper footing and balance 
at all times. 

Proper footing and balance enables better 

control of the product in unexpected situations.

 

Use safety equipment. Always wear eye protection. 

Dust mask, nonskid safety shoes, hard hat, or hearing 
protection must be used for appropriate conditions.

 

Do not use on a ladder or unstable support. 

Stable 

footing on a solid surface enables better control of the 
air compressor in unexpected situations.

AIR COMPRESSOR USE AND CARE 

 

Do not exceed the pressure rating of any component 
in the system. 

 

Protect material lines and air lines from damage or 
puncture.

 Keep hose and power cord away from sharp 

objects, chemical spills, oil, solvents, and wet floors. 

 

Check hoses for weak or worn condition before each 
use, making certain all connections are secure. 

Do not 

use if defect is found. Purchase a new hose or notify an 
authorized service center for examination or repair.

 

Release all pressures within the system slowly. 

Dust 

and debris may be harmful.

 

Store idle air compressors out of the reach of children 
and other untrained persons. 

Air compressors are dan-

gerous in the hands of untrained users.

 

Maintain air compressors with care.

 Follow mainte-

nance instructions. Properly maintained products are 
easier to control.

 

Check for misalignment or binding of moving parts, 
breakage of parts, and any other condition that may 
affect the product’s operation. If damaged, have the 
air compressor serviced before using. 

Many accidents 

are caused by poorly maintained products.

 

Keep the exterior of the air compressor dry, clean, and 
free from oil and grease.

 Always use a clean cloth when 

cleaning. Never use brake fluids, gasoline, petroleum-
based products, or any strong solvents to clean the unit. 
Following this rule will reduce the risk of deterioration of 
the enclosure plastic.

Summary of Contents for OL40135SS





















































Reviews: