background image

3 - English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper in-
terpretation of these symbols will allow you to operate the product better and safer.

SYMBOL

NAME

DESIGNATION/EXPLANATION

Safety Alert

Precautions that involve your safety.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand operator’s 
manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply with 
ANSI Z87.1.

Wet Conditions Alert

Do not expose to rain or use in damp locations.

No Hands Symbol

Failure to keep your hands away from the blade will result in serious 
personal injury.

Hot Surface

To reduce the risk of injury or damage, avoid contact with any hot 
surface.

V

Volts

Voltage

A

Amperes

Current

Hz

Hertz

Frequency (cycles per second)

W

Watt

Power

min

Minutes

Time

Direct Current

Type or a characteristic of current

Alternating Current

Type of current

no

No Load Speed

Rotational speed, at no load

.../min

Per Minute

Revolutions, strokes, surface speed, orbits etc., per minute

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL

SIGNAL

MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or serious 
injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or moderate 
injury. 

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but not related 
to a potential injury (e.g. messages relating to property damage).

Summary of Contents for JobMax R8223411





















Reviews: