Ricoh PRO C751 Troubleshooting Manual Download Page 19

Page: 19 / 76

When You Have Problems Operating the

Machine

This section describes common problems and messages. If other messages appear, follow the
instructions displayed.

Problem

Causes

Solutions

The operation switch
indicator continues blinking
and does not turn off when
pressed.

This occurs in the following
cases:

• The machine is

communicating with
external equipment.

• The hard disk is active.
• The machine is cooling

down.

Check if the machine is communicating
with external equipment.

The display is off.

The machine is in Energy
Saver mode.

Press the [Energy Saver] key to cancel
Energy Saver mode.

The display is off.

The operation switch is
turned off.

Turn on the operation switch.

Nothing happens when the
operation switch is turned
on.

The main power switch is
turned off.

Turn on the main power switch.

"Please wait." appears.

This message appears when
you turn on the operation
switch.

Wait for a while. If the machine does
not get ready in two minutes, contact
your service representative.

"Please wait." appears.

This message appears when
the machine is warming up.

• Wait for a while. If the machine

does not get ready in 10 minutes,
contact your service
representative.

• Wait until the message

disappears. Do not turn off the
main power switch while the
message is showing.

When You Have Problems Operating the Machine

Summary of Contents for PRO C751













































































Search results

Summary of Contents for PRO C751

Reviews:

Related manuals for PRO C751

Brands by name

Popular brands

Ricoh PRO C751, Troubleshooting Manual

Search results

Summary of Contents for PRO C751

Reviews:

Related manuals for PRO C751

Brands by name

Popular brands