Ricoh infoprint 1222 Service Manual Download Page 76

Page: 76 / 203

Diagnostic Information

2-41

Infoprint 1222

Paper Picks but Stops Half Way Through the Printer

FRU

Action

Input Paper Feed Sensor
RIP Card Assembly

Make sure the input paper feed
sensor is working properly.

Check for a broken or stuck flag on
the input paper feed sensor.

Make sure the cable is seated on the
RIP card assembly (J23).

5 V dc on pins #1, #4, #7,
and ground on pins #3, #6, and #9.
See

“Locations” on page 5-1

for

more information.

• If correct, replace the input paper

feed sensor.

• If the voltage is not correct,

replace the RIP card assembly.

Note: Always check printhead
alignment after replacing the RIP
card assembly. See

“Printhead

Assembly Adjustment” on
page 4-2

for hardware alignment

of the printhead.

Summary of Contents for infoprint 1222












































































































































































































Search results

Summary of Contents for infoprint 1222

Reviews:

Related manuals for infoprint 1222

Brands by name

Popular brands

Ricoh infoprint 1222, Service Manual

Search results

Summary of Contents for infoprint 1222

Reviews:

Related manuals for infoprint 1222

Brands by name

Popular brands