Ricoh Business Pro 1200 Operating Instructions Manual Download Page 35

Page: 35 / 81

IS LIT: LOAD PAPER

Not e: For a list of usable paper sizes,

☛

see page 66.

Not e: If you want t o change t he paper size,

☛

see page 44.

Non-recommended Paper For The Paper Cassette

❐

Folded, curled, or dam aged paper

❐

Torn paper

❐

Perforated paper

❐

Paper with conductive or low electrical resistance coating such as carbon
or silver coating

❐

Therm al paper, art paper

❐

Thin paper that has low stiffness.

Notes For Paper

❐

Do not copy onto the side of paper that has been already copied on.

❐

The following types of paper cannot be fed from the paper cassette. Load
them in the bypass feed entrance.

☛

See page 19.

✒

OHP transparencies

✒

adhesive labels

✒

translucent paper

❐

Correct curls in copy paper before loading.

❐

Fan copy paper to get air between the sheets before loading.

IS LIT: LOAD PAPER

Summary of Contents for Business Pro 1200


















































































Search results

Summary of Contents for Business Pro 1200

Reviews:

Related manuals for Business Pro 1200

Brands by name

Popular brands

Ricoh Business Pro 1200, Operating Instructions Manual

Search results

Summary of Contents for Business Pro 1200

Reviews:

Related manuals for Business Pro 1200

Brands by name

Popular brands