Ricoh Business Pro 1200 Operating Instructions Manual Download Page 34

Page: 34 / 81

IF YOU CANNOT MAKE COPIES

PROPERLY

Problem

Cause

Action

Copies appear
dirty.

The original has a gray or
colored background.

Adjust the im age
density.

☛

See

page 18.

The im age density is too
dark.

The platen cover or
exposure glass is dirty.

Clean them .

☛

See page 56.

The reverse side
of an original im -
age is copied.

The im age density is too
dark.

Adjust the im age
density.

☛

See

page 18.

Copies are too
light.

The original has a low
contrast im age.

Adjust the im age
density.

☛

See

page 18.

The im age density is too
light.

Dam p or rough grain paper
is used.

Use dry paper
w ithout rough
grain.

The sam e copy
area is dirty w hen-
ever m aking cop-
ies.

The platen cover or
exposure glass is dirty.

Clean them .

☛

See page 56.

Copies are blank
or parts of the im -
age are not cop-
ied.

The original is not set
correctly.

Set originals
correctly.

☛

See

page 10.

An im proper paper size is
selected.

Select the proper
paper size.

IF YOU CANNOT MAKE COPIES

PROPERLY

IF YOU CANNOT MAKE COPIES PROPERLY

Summary of Contents for Business Pro 1200


















































































Search results

Summary of Contents for Business Pro 1200

Reviews:

Related manuals for Business Pro 1200

Brands by name

Popular brands

Ricoh Business Pro 1200, Operating Instructions Manual

Search results

Summary of Contents for Business Pro 1200

Reviews:

Related manuals for Business Pro 1200

Brands by name

Popular brands