background image

 

12

O. Trouble Shooting: 

AC output does not stay ON. 

Some AC loads may not be large 

enough to hold the inverter ON. This condition is indicated by the 
inverter turning off after every eight to ten seconds, then back on 
again. The AC Status lamp will also be flashing orange.   
There are two possible solutions:   
Increase the sensitivity of the inverter by turning the Standby 
control 

slightly 

counter-clockwise until the lamp shows steady 

green; increase the amount of AC load on the inverter.   
         

Inverter shuts down due to Over Temperature.

 Your inverter 

will safely provide the output power defined in the technical data 
section under the conditions specified. If the inverter shuts down 
and indicates over temperature, it may be that you have exceeded 
one of the parameters.   

             

Check the following: 

Ensure the inverter has adequate ventilation. Insufficient 
ventilation can severely restrict the power output of your inverter.   
Ensure that the true power rating of your appliance (including 
power factor) is less than the output rating of your inverter. 

 

Inverter shuts down when trying to start a load. A sudden surge in 
load, such as a motor starting, may cause the inverter to shut 
down. If this occurs; ensure the battery voltage is within 
specifications when the device is trying to start: if the voltage falls 
too far, you may need to increase the size of your batteries.   
If the battery voltage is ok then the inverter power output may be 
too small. 

         

       

Common Problems: 
1. Television interference 

Operation of the power inverter can interfere with television 
reception on some channels. If this situation occurs, the 
following steps may help to alleviate the problem:   

 

Make sure that the chassis ground lug on the back of the 
power inverter is solidly connected to the ground system of 
your vehicle, boat or home:   

 

Do not operate high power loads with the power inverter while 
watching television.   

 

Make sure that the antenna feeding your television provides 
an adequate (“Snow free”) signal and that you are using good 
quality cable between the antenna and the television.   

 

Summary of Contents for INVERTEK L series


















Reviews: