manualshive.com logo in svg

Rice Lake MSI-8000, Technical Manual

Share
Download
Rice Lake MSI-8000 Technical Manual Download Page 25

ScaleCore Connect

© 

Rice Lake Weighing Systems 

●

 All Rights Reserved

21

3.2.3 Configuration

Auto Connect under configuration can be pressed to view available product. Use the rest of this menu to configure the product.

Figure 3-4. Configuration Display

Product Info

Product information is documented in this window.

  Do not change these settings without consulting Rice Lake Weighing Systems or a local dealer.

Figure 3-5. Product Info Settings

1. Select 

Configuration

, then 

Product Info

.

2. Enter the information for the product as follows:

Device ID

 – number given to the current product (Selections: 1-255)

User Defined Model

 – power source of current product

  Only 6V Battery and 110V AC (AC and 7-36V) are valid option for the MSI TranSend 7000 series products.

Figure 3-6. User Defined Model Selections

User Model Name

 – enter a name for the product

PCB Serial Number

 – serial number for the PCB board, read only

Product Serial Number

 – serial number of displayed product, read only

Software Version

 – displays the version of software currently installed, read only

3. Press 

 to save. New settings will not take affect until power is cycled on the product.

Note

Note

Summary of Contents for MSI-8000



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands