LONG MOUNTING PLATE (FOR NON-AUTOMATED UP-AND-OVER
DOORS)
Code ACG8188
Position the mounting plate with the upper section (slotted hole to feed electric cable) in
top position (Fig. 6).
Fix the mounting spar flush against the upper moving part of the up-and-over door distance
of
17 cm
from the internal cable of the sheath using 6.3 x 13 self-tapping screws (not
included).
SHORT MOUNTING PLATE (FOR AUTOMATED UP-AND-OVER DOORS)
Code ACG8189
Calculate the length,
L = C - 410 [mm]
, to which the mounting plate should be vertically
fixed (Fig. 7-8).
Position it on the appropriate vertical supports while keeping the upper part
(slotted hole to feed electric cable) in a vertical position facing upwards.
Fix the mounting plate distance of
17 cm
from the internal cable of the sheath using the
four feedthrough holes, four 4 metric screws (M6x25) and self-locking nuts (not supplied).
After the assembly’s completion, either with the LONG
MOUNTING PLATE or with the SHORT MOUNTING PLATE,
the reducer’s outlet-shaft must be placed in a distance
of
80±10 mm
from the pivot-axle of the up-and-over
door’s little arm.
LEVER APPLICATION
ASSEMBLY OF PAIR OF STRAIGHT LEVERS (code ACG8720) BETWEEN MOTOR AND
UPPER DOOR FRAME
N.B.: THE PAIR OF STRAIGHT TELESCOPIC LEVERS can be mounted when there is
a 15 mm minimum space guaranteed between the moving part of the door
and the exterior door frame containing the counterweight.
- Rivets or screws should be used to fix corner parts to the upper frame, in line with
measurements shown in Fig. 4:
if at the measurement of 35 mm, one finds the
reinforcing plate of the door frame, it is possible to fix the brackets directly
above this reinforcing plate even if the measurement will not be maintained.
In the event that the up-and-over door is already pre-fitted for automated movement, use
the attachments provided.
Do not use the angles provided.
- Insert the sliding arm sleeve into the angles and secure the pivots and split pins (Fig. 4).
- Make sure that the casing does not touch the up-and-over door movement levers when
mounted.
ASSEMBLY OF PAIR OF CURVED LEVERS (code ACG8722) BETWEEN MOTOR AND
UPPER DOOR FRAME
N.B.: The PAIR OF CURVED TELESCOPIC LEVERS should be mounted when there is
less than the 15 mm minimum space guaranteed between the moving part
of the door and the exterior door frame containing the counterweight.
-
In the event that the up-and-over door is already pre-fitted for automated movement, use
the attachments provided.
Do not use the angles provided.
- Insert the sliding arm sleeve into the angles and secure the pivots and split pins (Fig. 4).
- Make sure that the casing does not touch the up-and-over door movement levers when
mounted.
ANGLE IRONS
40 mm
ANGLE IRONS
LEVERS SLEEVE
LEVERS SLEEVE
5A
5B
Note: The length of the sleeve and of the sliding arm must be modified in function of overhead door height. Trim the sleeve and the sliding arm so that the sleeve rests
40 mm from the center of the drawbar pivot pin and the sliding arm avoids contact with the rotating dowels located on the angles (Fig. 5A)
4
35 mm
55 mm
INSTALLATION OF 2 MOTOR BOSS ON DOORS UP TO 12 m
2
G
B
C
L
L = C - 410 mm
max 83 cm
7
8
L
6
17 cm
Summary of Contents for AA40845
Page 14: ...14 62 63 59 60 61 64 I...
Page 28: ...28 62 63 59 60 61 64 F...
Page 42: ...42 G B 62 63 59 60 61 64...
Page 46: ...NOTES 46...
