
SAFETY
Only tow the Implement behind a properly sized and equipped Tractor which
exceeds the weight of the Implement by at least 20%. DO NOT tow the
Implement behind a truck or other type of vehicle. Never tow the Implement
and another Implement connected in tandem. Never tow the Implement at
speeds over 20 MPH.
(STI-06)
Your driving vision may be reduced or impaired by the tractor, cab, or implement. Before driving
on public roadways identify any limited vision areas, and make adjustments to your operating
position, mirrors, and the implement transport position so that you can clearly see the area
where you will be traveling, and any traffic that may approach you. Failure to maintain adequate
vision of the public roadway and traffic can result in serious injury or even death.
(STI-10)
SA
F
ET
Y
When the cutting head is folded for transport, the center of gravity of the Tractor is raised and
the possibility of overturn or tip-over is increased. Serious injury or even death could result from
a tractor turnover. Turn slowly and use extra care on hillsides. Never fold the cutting head while
on a hillside as the tractor might overturn.
(SDM-2)
Maintenance and Service Safety Instructions and Practices
Make sure the PTO shield, integral driveline shields, and input shields are
installed when using PTO-driven equipment. Always replace any shield if it is
damaged or missing.
(S3PT-8)
Relieve hydraulic pressure prior to doing any maintenance or repair work on
the Implement. Place the Implement on the ground or securely blocked up,
disengage the PTO, and turn off the tractor engine. Push and pull the
Remote Cylinder lever in and out several times prior to starting any
maintenance or repair work.
(S3PT-09)
Always disconnect the main PTO Driveline from the Tractor before performing service on the
Implement. Never work on the Implement with the tractor PTO driveline connected and
running. Rotating Parts, Blades or Drivelines could turn without warning and cause immediate
entanglement, injury or death.
(S3PT-11)
Always maintain the safety signs in good readable condition. If the safety signs are missing,
damaged, or unreadable, obtain and install replacement safety signs immediately.
(SG-5)
AGM 52-62-72-82
10/10
Safety Section 1-14
© 2010 Alamo Group Inc.
Summary of Contents for AGM52
