RHINO MOTION CONTROLS RMCS-1110 Installation Manual And Datasheet Download Page 15 | Manualshive

Page: 15 / 25

background image

RHINO MOTION CONTROLS

RMCS-1110
Hybrid Servo Driver with Modbus RTU communication
(Max. 80Vdc and 7A per phase)

http://www.rhinomc.com

Page 15

Hybrid AC Driver [RMCS-1110]

2-phase, 4-lead Motors Connections

4 lead motors are the least flexible but easiest to wire. Speed and torque will depend on winding
inductance. In setting the drive output current, multiply the specified phase current by 1.4 to determine
the peak output current.

«
...
13
14
15
16
17
...
»

Summary of Contents for RMCS-1110


























Reviews:

No comments

Related manuals for RMCS-1110

Fuji Electric MICRO-SAVER AF-300

Brand: GE Pages: 78

Brand: GE Pages: 50

Brand: Masterflex Pages: 20

Brand: Danfoss Pages: 246

Brand: Mesa Pages: 41

Brand: Piezoconcept Pages: 8

Brand: Metronix Pages: 36

Brand: DALCNET Pages: 4

Brand: Simu Pages: 24

Brand: Astraada Pages: 387

apfiff09 marine

Brand: Vacon Pages: 310

MOVIMOT MM D Series

Brand: SEW-Eurodrive Pages: 200

Brand: Melec Pages: 43

Brand: Melec Pages: 44

Brand: Melec Pages: 48

Planetgear 7000

Brand: Rexnord Pages: 33

Brand: Melec Pages: 48

Brand: Binks Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands