background image

17

INSTALLATION - WATER HEATER

FLUEING

This water heater does not require additional flueing. A secondary flue must not be

installed.

FROST PROTECTION

The water heater may have frost protection. Refer to the rating label on the water

heater. The frost protection system will protect the water heater from damage, by

preventing ice forming in the waterways of the water heater, in the event of freezing

occurring. Models without frost protection are not covered under warranty for damage

caused by freezing and must not be installed in areas subject to frost conditions.

The frost protection system will be rendered inoperable if electrical power is not

available at the water heater. Damage to the water heater caused by freezing of the

pipework to or from the water heater is not covered under warranty.  Refer to AS/

NZS 3500 for precautions to be taken for installations in frost prone areas. The

water heater is not suitable for installation in areas where the ambient temperature

falls below -20ºC (including wind chill factor).

WATER SUPPLY

Where the water supply pressure exceeds that shown below, an approved pressure

limiting valve is required and should be fitted as shown in the installation diagram

(refer to page 18).

Notes:

It is not recommended to install this water heater with a low pressure water

supply.

This water heater is not suitable for connection to bore water or spring water

unless a water treatment device is fitted.

If sludge or foreign matter is present in the water supply, it is recommended a

suitable filter be incorporated in the cold water supply pipe to the water heater.

Refer to Water Supplies on page 27.

HOT WATER DELIVERY

The delivery water temperature requirements of AS/NZS 3500.4 must be considered.

We recommend and it may also be required by regulations, that a temperature limiting

device be fitted for any ablution area, such as a bathroom or ensuite.

*   minimum water supply pressure required to

achieve the rated flow and performance.

Model

Water Pressure kPa

Maximum

Minimum *

18

20

24

1000

1000

1000

140

140

140

Summary of Contents for 871 018





























Reviews: