manualshive.com logo in svg

RH Baby&child MARCELLE, Instructions Manual

Share
Download
RH Baby&child MARCELLE Instructions Manual Download Page 7

Page  7  of  10

LOCK

WASHER

B

C

DETAIL C

DETAIL D

HEX NUT

PLAIN

WASHER

ALLEN BOLT

(BB)

ALLEN
WRENCH

ALLEN WRENCH

OPEN WRECH

HEX  NUT

LOCK WASHER

PLAIN WASHER

MATTRESS
SUPPORT

STABILIZER RAIL

HARDWARE NEEDED FOR STEP #2:

(BB) 1/4" X 1-1/4" BOLT = 8 PCS

LOCK WASHER = 8 PCS

PLAIN WASHER = 8 PCS

HEXAGONAL NUT = 8 PCS

STEP #2

MATTRESS SUPPORT  ARM ASSEMBLY

STABILIZER RAIL ASSEMBLY

MATTRESS HEIGHT ADJUSTMENT

STEP #2.1

Lay Mattress Support flat with Stabilizer Rail on each side.

NOTE:

Each end of the arm of the Mattress Support has a hole for the bolt to

pass through that corresponds to the holes located in the frame of the

Mattress Support.

STEP #2.2:

Insert the bolt into the desired hole of the frame through the hole on the

arm support. Fasten the bolt with plain washer, lock washers &

hexagonal nut  provided. Repeat procedure on other arms of the

Mattress Support. See 

DETAIL C

.

WARNING:

Set the Mattress Support to the desired height by adjusting the Support

Arms. The Mattress Support should be at its highest setting for

newborns, then adjusted to the lower positions as the child grows and

becomes mobile. Once the child is able to stand, the Mattress Support

should be at its lowest position.

STEP #2.3:

Install the Stabilizer Rail at ends of the arm support, as illustrated in

DETAIL D

.

OPEN WRENCH = 1 PC

ALLEN WRENCH = 1 PC

ALLEN BOLT

(BB)

ALLEN BOLT

(BB)

ALLEN BOLT

(BB)

ALLEN BOLT

(BB)

Summary of Contents for MARCELLE











Reviews:

No comments

Brands by name

Popular brands

Load more brands