background image

Page  4  of  10

IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS

     WARNING: ENTRAPMENT / STRANGULATION HAZARD

Infants have died in toddler beds from entrapment and strangulation.

Failure to follow these warnings and the assembly instructions could 

result in serious injury or death.

NEVER

 use bed with children under 15 months.

NEVER

 place bed near windows where cords from blinds or drapes 

may strangle a child.

·

The mattress intended for use on the bed shall be a full-size crib mattress

having minimum dimensions of 51-5/8 inches (1310mm) in length, 27-1/4

inches (690mm) in width and 4 inches (100 mm) in thickness, not

exceeding 6 inches (152 mm) in thickness.

·

If guardrails are used as the mattress containment means, guardrail(s)

provided must be used to avoid the formation of a gap between the

mattress and the bed that could cause an entrapment.

·

DO NOT place bed near windows where cords from blinds or drapes may

strangle a child.

·

DO NOT place items with a string , cord, or ribbon around a child’s neck,

such as hood strings or pacifier cords.

·

DO NOT suspend strings over a toddler bed for any pacifier cords.

·

A child using the toddler or day bed shall be at least 15 months of age

and shall not weigh more than 50lbs (22.7kgs).

Summary of Contents for MARCELLE











Reviews: