background image

 

 
12. 

 

Do not remove material from the platform until it has stopped completely. 

 
13. 

 

Keep out from under a raised load.  

 
14. 

 

Never stand in-line with the raising or lowering of the platform at either the top or bottom of the hoist track. 

 
15. 

 

Never hoist over an open doorway.   

 
16. 

 

Never exceed the Rated Load Capacity of 200 pounds for the PRO200 hoist, or 400 pounds for the PRO400 hoist.  
The Rated Load Capacity is the maximum load that should ever be applied to the hoist.  

 
17. 

 

Avoid sudden stops and shock loads.

 

 
18. 

 

No person shall be allowed to ride on the hoist. 

 
19. 

 

NEVER 

climb the track; use a ladder. 

 
20. 

 

Check the hoist periodically during operation.  Know how to stop the PRO Drive quickly in case of emergency. 

 
21. 

 

Do not attempt to make adjustments while the PRO Drive is being operated.

 

 

22. 

 

If the engine or motor fails during operation, release control lever to prevent load from falling.

 

 

23. 

 

Keep all body parts clear of moving parts.

 

 

24. 

 

Do not operate PRO Drive when brake rope is wet.

 

 

25. 

 

Do not operate PRO Drive when under the influence of drugs, alcohol, or medication.

 

 
26. 

 

At end of operation, the PRO Drive should be secured to prevent unauthorized use.  Never

 

assume you will find the 

PRO Drive in the same condition in which you left it.

 

 
27. 

 

Do not weld or otherwise modify the PRO Drive.  Such alterations may weaken the structural integrity of the hoist and 
will void your warranty.

 

 

28. 

 

Only trained personnel are authorized to do repairs.

 

 
 

 

Summary of Contents for PRO Drive E




























Reviews: