background image

F.  NO EXTENSION OF STATUTE OF LIMITATIONS 

 

ANY REPAIRS PERFORMED UNDER EITHER OF THESE WARRANTIES SHALL NOT IN ANY WAY 
EXTEND THE ONE-YEAR AND FIFTEEN-YEAR STATUTES OF LIMITATIONS CONTAINED IN THIS 
LIMITED WARRANTY. 
 

G.  PROCEDURE FOR WARRANTY PERFORMANCE 

 

If the product fails to perform to the Manufacturer’s specifications, the Buyer must contact the dealer from whom the product 
was purchased.  The Buyer must provide the dealer with the applicable model and serial numbers, the date of purchase, and 
the nature of the problem. 
 

H.  PREAPPROVAL OF LABOR COSTS 

 

All labor costs related to a dealer’s performance of the warranty obligations under this limited warranty must be pre-approved 
by Reimann & Georger Corp. Marine Products. 

 

I.  NO OTHER EXPRESS WARRANTIES 

 

THE MANUFACTURER IS NOT SUBJECT TO ANY EXPRESS WARRANTIES OTHER THAN THOSE SET 
FORTH ABOVE. 
 

J.  LIMIT ON DURATION OF IMPLIED WARRANTIES 

 

THE DURATION OF ANY IMPLIED WARRANTIES UNDER APPLICABLE STATE LAW RELATING TO THE 
PURCHASE OF THIS PRODUCT SHALL BE LIMITED TO A PERIOD OF ONE (1) YEAR FROM THE DATE 
OF PURCHASE. 
 

Some States do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. 
 

K.  QUESTIONS REGARDING LIMITED WARRANTY 

 

Any questions regarding this limited warranty or the procedure which the consumer should follow in order to obtain 
performance of any warranty obligation may be addressed to either the dealer from whom this product is purchased or to 
Reimann & Georger Corp. Marine Products, 1849 Harlem Rd., Buffalo, NY 14212. 
 

L.  EXCLUSIONS FROM LIMITED WARRANTY.  THIS LIMITED WARRANTY DOES NOT COVER ANY OF 

THE FOLLOWING: 

 

1. 

 

Equipment which has been abused, damaged, used beyond rated capacity, or which is damaged or has defects caused by 
repairs or service completed by persons other than authorized service personnel. 

 
2. 

 

Costs of repairing damage caused by environmental factors which include, but are not limited to, airborne fallout, 
chemicals, tree sap, salt, ocean spray, and water hazards. 

 
3. 

 

Damage caused by acts of God which include, but are not limited to, hailstorms, windstorms, tornadoes, sandstorms, 
lightning, floods, and earthquakes. 

 
4. 

 

Damage under conditions caused by fire or accident, by abuse or negligence, by improper installation, by misuse, by 
incorrect operation, by “normal wear and tear”, by improper adjustment or alteration, by alterations not done by the 
Manufacturer, or by failure of product parts from such alterations. 

 
5. 

 

Costs of repairing damage caused by poor or improper maintenance, costs of normally scheduled maintenance, or the cost 
of replacing any parts unless done as the result of a repair covered by your one-year limited warranty. 

 
6. 

 

Costs of modifying the product in any way once delivered to the Buyer, even if such modifications were added as a 
production change on other products made after the Buyer’s product was built. 

 
 

1303 

Summary of Contents for HL40120


































Reviews: