RFM CCT24 Series Integration Manual Download | Manualshive

Page: 57 / 90

background image

Page 57 of 90

CCT24

GpioAlt

bit is set for GPIO4, the corresponding

GpioSleepMode

bit is ignored and GPIO4 is controlled

directly by the

GpioSleepState

parameter bit 7.

GPIO_SleepDir

- when

GPIO_SleepMode

is enabled, this parameter functions as a secondary

GPIO_Dir

to set the direction of the GPIOs during a device’s sleep period. This enables the user to provide alternate
configurations during sleep that will help minimize current consumption. Bits 0..5 correspond to GPIO0..
GPIO5. Set a

GPIO_SleepDir

bit to 1 to specify an output, or to 0 to specify an input.

GPIO_SleepState

- when

GPIO_SleepMode

is enabled, this parameter functions as a bitmask to control

the states of the GPIOs, the RADIO_TXD output, and the /HOST_CTS and /DCD outputs during a de-
vice’s sleep period. This allows the user to set alternate configurations during sleep to minimize current
consumption. Bits 0..5 correspond to GPIO0..GPIO5 respectively. Bit 6 sets the state of RADIO_TXD,
and bit 7 sets the states of /HOST_CTS and /DCD. A sleep state bit is set to 1 to specify a high output, or
to 0 to specify a low output. Bit 6 must be set low in order to achieve minimum sleep current (high imped-
ance load assumed), and the other bits may need to be set low or high depending on their external loads.
When bit 6 is set low, expect a serial “break” condition to occur as the module wakes from sleep. The
serial break condition can be eliminated by setting bit 6 high, but sleep current will be increased.

PWM0_Init

- this parameter sets the initial value for PWM0 at startup.

PWM1_Init

- this parameter sets the initial value for PWM1 at startup.

ADC_SampleIntvl

- this parameter sets the interval between the beginning of one ADC read cycle and the

next ADC read cycle. The three ADC inputs are read on each ADC read cycle. Each

ADC_SampleIntvl

count equals 10 ms. This interval will be the worst-case latency for ADC generated interrupts. This inter-
val is independent of the

IO_ReportInterval

as the ADCs will be read again on that interval.

ADC0..2_ThresholdLo/Hi

- these values define thresholds to trigger an I/O report based on ADC meas-

urements. If I/O reporting is enabled, a single EVENT report containing the contents of the I/O bank is
generated when a threshold is crossed. Reporting is "edge-triggered" with respect to threshold bounda-
ries, not "level-triggered"; i.e., if the measurement remains there, additional reports are not triggered until
the value crosses the threshold again. The thresholds are met whenever one of the following inequalities
are satisfied:

ADC

x

< ADC

x

_ThresholdLo

ADC

x

> ADC

x

_ThresholdHi

IO_ReportTrigger

- when a selected trigger source is enabled, a trigger event will cause the remote to

send an EVENT message to its base containing the entire current values of the I/O Register Bank from
GPIO0 up to and including the

EventFlags

, but not the PWM settings which are output-only.

bit 7

ADC2 high/low thresholds

bit 6

ADC1 high/low thresholds

bit 5

ADC0 high/low thresholds

bit 4

Periodic report timer

bit 3

GPIO3 edge

bit 2

GPIO2 edge

bit 1

GPIO1 edge

bit 0

GPIO0 edge

I/O reporting is supported for remotes only, not the base.

«
...
55
56
57
58
59
...
»

Summary of Contents for CCT24 Series



























































































Reviews:

No comments

Related manuals for CCT24 Series

Brand: Handic Pages: 21

Brand: Accurate Technology Pages: 20

Brand: R&S Pages: 220

Brand: YOKOGAWA Pages: 48

Brand: IDS Pages: 24

Brand: Uniden Pages: 17

Brand: Tech3E Pages: 8

Brand: Kathrein Pages: 21

EchoStream EN1215EOL

Brand: Inovonics Pages: 2

Brand: Nautel Pages: 200

Realvision RV-220P

Brand: Raymarine Pages: 24

Brand: Yaesu Pages: 13

FT-FOTR-1V-ST-S

Brand: Fiber Tronix Pages: 4

AXIS TX PICO PLUS

Brand: Wave Central Pages: 15

RF340-4PR-ASL-NIS

Brand: GAMA Electronics Pages: 5

Brand: E+E Elektronik Pages: 40

Brand: Onkyo Pages: 50

Brand: Cable AML Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands