background image

3

I-RIH (05-21) 131793-A

Table 1.  Related Technical Manuals Available from Factory Distributor

Type

Form

*

PN

Replacement parts

P-RIH-VR

272513

*

Also available at 

www.reznorhvac.com

 .

GENERAL INFORMATION

These infrared heaters are designed and manufactured in compliance with the American National Standards Institute . 

They are design-certified by the Canadian Standards Association to ANSI Standards for installation in the United 

States and to CAN/CSA Standards for installation in Canada . These units are approved for indoor commercial and 

industrial installation only . Installation should be done by a qualified agency in accordance with these instructions 

and in compliance with all codes and requirements of authorities having jurisdiction .

References

Important Safety Information

Please read all information in this manual thoroughly and become familiar with the capabilities and use of your 

appliance before attempting to operate or maintain this unit . Pay attention to all dangers, warnings, cautions, and 

notes highlighted in this manual . Safety markings should not be ignored and are used frequently throughout to 

designate a degree or level of seriousness .

DANGER: 

A danger statement describes a potentially hazardous situation that if not avoided, will result in severe 

personal injury or death and/or property damage .

WARNING: 

A warning statement describes a potentially hazardous situation that if not avoided, can result in severe 

personal injury and/or property damage .

CAUTION:

 A caution statement describes a potentially hazardous situation that if not avoided, can result in minor 

or moderate personal injury and/or property damage .

NOTE: 

A note provides important information that should not be ignored .

⚠ DANGER ⚠

 

• Gas-fired appliances are not designed for use in hazardous atmospheres containing flammable 

vapors or combustible dust, in atmospheres containing chlorinated or halogenated hydrocarbons, 

or in applications with airborne silicone substances.

 

• This product can expose you to chemicals including lead, which is known to the State of California 

to cause cancer and birth defects or other reproductive harm. For more information go to 

www.

P65Warnings.ca.gov

.

 

• These infrared heaters are operated without venting (refer to 

Ventilation Requirements

 section).

⚠ WARNING ⚠

 

• These infrared heaters SHOULD NOT BE USED in the following applications: 

•  Enclosed swimming pool areas 

•  Areas with contaminated atmospheres 

•  Outdoor applications 

•  Residential applications 

•  Areas requiring explosion-proof equipment 

•  Process heating applications

Summary of Contents for RIHL

























Reviews: