Reynolds Building Systems the Fairview Assembly Book Download Page 6 | Manualshive

Page: 6 / 24

background image

Tongue Edge

LAP Edge

The siding is made in 4x8 sheets with grooves
cut into the face, the long edge is beveled so
that the siding overlays where they butt.

To identify which edge we want you to use, we
will refer to the edge as either the 'LAP' Edge
or the Tongue Edge. Nail siding with 8d galv.
nails, spaced 12" apart.

Exterior Siding

Step 3

Install Siding on Gables

1.

Select one of the gable frames, Turn the gable over letting the bottom plate overhang

the floor so the gable lays flat.

2.

Install gable siding using 6d galv. nails.

LAP

Edge

LAP

Edge

Install Siding on Ends

Siding Extends 3/4"

Below Bottom Plate

3.

Install siding on the other gable frame.

«
...
4
5
6
7
8
...
»

Summary of Contents for the Fairview

























Reviews:

No comments

Related manuals for the Fairview

Brand: Palmako Pages: 53

Brand: Palmako Pages: 101

Brand: Palmako Pages: 61

Brand: G21 Pages: 32

Brand: Palmako Pages: 56

Brand: Keter Pages: 27

Brand: Kerbl Pages: 2

Brand: Keter Pages: 40

Brand: Palmako Pages: 108

Brand: Palmako Pages: 50

Brand: Palmako Pages: 104

Brand: Forest garden Pages: 2

HA28001-4163162451-21-0000-20

Brand: megiw Pages: 35

HA28001-3163162453-12-0000-20

Brand: megiw Pages: 30

Pavilion Octagon

Brand: Bertsch HolzBau Pages: 8

Brand: Bertsch HolzBau Pages: 8

the Garden Shed

Brand: Best Barns Pages: 24

Modular Garden MGPAV-01

Brand: Palmako Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands