Reynolds Building Systems the Fairview Assembly Book Download Page 12 | Manualshive

Page: 12 / 24

background image

flush

Step 9

Install Trim on Back Wall Panel

Side

Wall

1x4 Trim

1x4 - 75 3/4" Corner Trim

1.

Install 1x4-75 3/4" corner trim boards to the back wall. Install trim

flush with the 2x4 top plate and flush with the siding on the sidewalls.
Use 8d galv. nails, spaced 12" apart.

2.

Cut 1x4-6' trim boards and install between the corner trim boards.

Install Trim Flush

with Top Plate

Back Wall

Panel

Step 10 Assemble Porch Material

1.

Butt (2) two 70-1/2" long 2x4s, with OSB fillers

attached to one side, together.

2.

Install a 47" long 2x4 between the top 2x4

boards. Apply glue and nail with 10d sinkers.

70-1/2" 2x4 with OSB

47" Long 2x4

3.

Install a pre-cut 2x6 treated board to the bottom

of each porch post. Use a 2-1/2" wood screw.

«
...
10
11
12
13
14
...
»

Summary of Contents for the Fairview

























Reviews:

No comments

Related manuals for the Fairview

Brand: Palmako Pages: 33

G-kit Bonanza 1m2

Brand: G-Tools Pages: 12

Brand: Universo Consumer Products Pages: 24

Brand: Palmako Pages: 153

GardenSaver GS84D-Plywood

Brand: OLT Pages: 33

Brand: Palmako Pages: 55

Brand: Palmako Pages: 55

Brand: Palmako Pages: 25

Premier 30232GK-PTX

Brand: ABSCO SHEDS Pages: 21

Brand: vidaXL Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands