Reynolds Building Systems Best Barns USA Glenwood Assembly Book Download

Page: 19 / 20

Supplement Details

Pre-built Header

If you purchased the optional entry door, locate where you want the opening to be and

install the 37-1/2" door header between two wall studs.

Secure the header by nailing through the top plate and wall studs with 10d sinkers.

Cut (2) two header supports from pre-cut wall studs and install under the door header.

2x4 Header Support

Install Roofing — Not Supplied in Kit

Install metal roof edging along the end walls and

the front edge of the roof sheathing.

Install shingles according to the instructions on the wrapper.

If you need more detailed instructions on installing shingles,
there are good publications at book stores or newsstands.

Roof Sheathing

1x6

Trim

Metal Roof Edge

2x4 Overhang

Summary of Contents for Best Barns USA Glenwood





















Search results

Summary of Contents for Best Barns USA Glenwood

Reviews:

Related manuals for Best Barns USA Glenwood

Brands by name

Popular brands

Reynolds Building Systems Best Barns USA Glenwood, Assembly Book

Search results

Summary of Contents for Best Barns USA Glenwood

Reviews:

Related manuals for Best Barns USA Glenwood

Brands by name

Popular brands