Reynolds Building Systems Best Barns Fairview Assembly Book Download Page 25 | Manualshive

Page: 25 / 28

background image

Cross Buck

Trim

.

.

.

.

.

2x4-6' Door

Stiffener

2x4 Blocks to

Level Door

2x4 Gouge

Block

Step 29 Install Door Stiffener on Single Door

1.

Locate the door that has a 2x4 fastened, on edge, to

the back side of the door. See Step 24.This is the
right door. Lay the door with the trim facing up and
install 5" hinges to the left side of the door trim. To
position the hinge properly, hold the rectangular plate
against the frame. Use 1-3/4" black screws..

2.

Install hinges to the left side of the other door.

Step 28 Install Hardware

Install Hinges on Double Barn Doors

Install the door hinges on the opposite side of the door if
you want the door to open in the opposite direction

Locate the 28" wide door. This door will be installed in the front door opening. The instructions
below describe installing a 2x4 as a door stiffener. Decide which way the door will open and secure
the 2x4 on the opposite side where the hinges will be installed.

1.

Locate a 68-1/2" long 2x4 and position the 28" door with trim facing up. Place the 2x4 on

edge under the door. The 2x4 should be 1-1/2" from long edge of trim and 1-1/2" from bottom
of trim. Use a 2x4 block as a gauge and another to help level door while installing 2x4.

2.

Fasten the 2x4 to the door using (6) six 2-1/2" long deck screws. Install the first screw 6" from

the bottom of the door. Space the remaining screws 12" apart.

3.

Install hinges as described in Step 28 on opposite side of 2x4.

«
...
23
24
25
26
27
...
»

Summary of Contents for Best Barns Fairview





























Reviews:

No comments

Related manuals for Best Barns Fairview

SpaceSaver SS124-SLIDER-METAL-AK

Brand: OLT Pages: 39

Brand: Keter Pages: 19

Brand: Grosfillex Pages: 88

Brand: Luoman Pages: 40

Brand: Baltic Connexions Oü Pages: 16

5x5 Corner Playhouse

Brand: Walton Pages: 7

Brand: Palmako Pages: 153

Lara FRB28-3524

Brand: Palmako Pages: 44

Roger FR44-5953-1

Brand: Palmako Pages: 101

Brand: Palmako Pages: 54

Brand: Palmako Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands