Reynolds Building Systems Best Barns Fairview Assembly Book Download Page 11 | Manualshive

Page: 11 / 28

background image

58-1/2" Bottom Plate

48" Bottom Plate

48" Top Plate

11" Bottom Plate

11" Top Plate

X

X

X

X

X

X

X

X

X

X

X

X

X

X

R

R

6.

Position (2) two 58-1/2" long 2x4s together and

indicate with 'X' marks where wall studs will be
located. Mark the right most stud location with 'R'.

Step 9

Assemble Sidewalls - Double Doors Offset

11-1/2"

1.

Locate (1) one 34-3/4" long board and cut (2) two boards 11" plates from this board.

2.

Install (2) two 72" wall studs between 11" wall plates. See layout below. Use 10d sinkers.

3.

Position (2) two 48" long 2x4s together and indicate with 'X' marks where walls studs will be

located.

Double Stud

Here

Install Stud

Centered In

Frame

Install Stud

Centered In

Frame

71-1/2" Header Support

48" Wall Plate

Center Stud

4.

Install (4) four 72" wall studs between 48" wall plates.

5.

Locate (2) two 72" long 2x4s and cut each to 71-1/2".

Install these as a header support on each wall frame
flush with bottom plate. Use 10d sinkers.

58-1/2" Wall Plate

11-1/2"

Center Stud

7.

Install (4) four 72" wall studs between 58-1/2" plates.

«
...
9
10
11
12
13
...
»

Summary of Contents for Best Barns Fairview





























Reviews:

No comments

Related manuals for Best Barns Fairview

Brand: Palmako Pages: 21

Brand: Palmako Pages: 29

Brand: Palmako Pages: 138

Brand: Solid Pages: 33

Brand: Solid Pages: 34

Brand: Universo Consumer Products Pages: 20

Brand: G21 Pages: 40

Brand: Palmako Pages: 65

SS84-SLIDER-METAL-AK

Brand: OLT Pages: 36

Brand: OLT Pages: 36

SunShed Greenhouse 8x12

Brand: OLT Pages: 38

Brand: Palmako Pages: 54

Brand: Palmako Pages: 103

MIKKEL EL16-1811

Brand: Palmako Pages: 67

10.5 Ft x 13 Ft WoodBridge Plus

Brand: DuraMax Pages: 10

Brand: DuraMax Pages: 68

Brand: VISSCHER Pages: 84

ELEGANTO TOP 5436

Brand: telluria Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands