background image

2  Important Directions for Use

2.1  Appropriate Use

Bosch  Rexroth  products  represent  state-of-the-art  developments  and  manufac-

turing. They are tested prior to delivery to ensure operating safety and reliability.
The products can only be used in the appropriate way. Otherwise, situations re-

sulting in property damage and personal injury may occur.

Bosch Rexroth as manufacturer is not liable for any damages result-

ing  from  inappropriate  use.  In  such  cases,  the  guarantee  and  the

rights  to  payment  of  damages  resulting  from  inappropriate  use  are

forfeited. The user alone carries all responsibility of the risks.

Before  using  Bosch  Rexroth  products,  make  sure  that  all  the  pre-requisites  for

appropriate use of the products are satisfied.

Personnel that in any way or form use our products must first read and under-

stand the relevant safety instructions and be familiar with appropriate use.

If the products take the form of hardware, they must remain in their original

state, in other words, no structural changes are permitted.

It is not permitted to decompile software products or alter source codes.

Do not mount damaged or faulty products or use them in operation.

Make sure that the products have been installed in the manner described in

the relevant documentation.

2.2  Inappropriate Use

Using the brake choppers outside of the operating conditions described in this

documentation and outside of the indicated technical data and specifications is

defined as "inappropriate use".
Brake choppers shall not be used under following conditions:

They are subject to operating conditions that do not meet the specified ambi-

ent  conditions.  These  include,  for  example,  operation  under  water,  extreme

temperature fluctuations or extremely high temperatures.

Furthermore, the brake choppers shall not be used in applications which have

not been expressly authorized by Rexroth. Please carefully follow the specifi-

cations outlined in the general Safety Instructions!

Bosch Rexroth AG
Important Directions for Use

 Brake Chopper

12/65

DOK-RCON03-EFC*BRAKE**-IT01-EN-P

Summary of Contents for EFC x610 Series









































































Reviews: