manualshive.com logo in svg

Rexnord Falk Drive One DB, Owner'S Manual, Page: 22 / 27

Share
Download
Rexnord Falk Drive One DB Owner'S Manual Download Page 22

Appendix E 

•

 Falk

™

 Drive One

®

 Enclosed Gear Drives

(Page 22 of 27) 

Type D Series 

•

 Sizes M1130 thru M1210

168-050

 

Rexnord Industries, LLC, 3001 W. Canal St., Milwaukee, WI 53208-4200

January 2019 

Telephone: 414-342-3131 Fax: 414-937-4359

Supersedes 04-11 

e-mail: [email protected] web: www.rexnord.com

(PN 2124650)

7.  A temperature switch is provided to control oil sump 

temperature. See Figure 2 for proposed wiring. 

There are two separate circuits in the temperature 

switch. The low circuit is to operate the electric fan. 

It is recommended the fan motor be operated by 

the temperature switch through a motor starter relay 

(consult applicable local and national electrical codes). 

The high circuit is provided to operate either a high 

temperature alarm or main motor shutdown.

L

1

L

2

PROPOSED TEMPERATURE SWITCH WIRING

DIAGRAM FOR ELECTRIC FANS

CONTROL VOLTAGE

SWITCH

FALK PART NO.

932716

 - NEMA 4 & 13

LOW CIRCUIT

START FAN

MOTOR

MS

RED

BLUE

PURPLE

SET AT 140°F

(60°C)

HIGH CIRCUIT

YELLOW

ORANGE

ALARM OR MAIN MOTOR

CIRCUIT

BROWN

SET AT 210°F

(100°C)

MS = MOTOR STARTER

CUSTOMER WIRING

AND COMPONENTS

 

AC RATING - INDUCTIVE LOAD - 50% PF

   DC RATING - INDUCTIVE LOAD - L/R = 0.26

AC

VOLTS

AMP

AMP

DC

VOLTS

125

250

480

15

15

15

 

MAXIMUM CONTINUOUS CURRENT

∗∗ 

Reference only.

6-12 **

24 **

125

250

15

5
0.05
0.03

Figure 2

POSITION A

POSITION B

POSITION C

1

1

2

Mounting Positions

For Position 

A & B 

Remove Plug 1

For Position 

C 

Remove Plug 2

Note: Never use 

copper or brass 

fastening materials

Figure 3

8.  Connect power to the motor using an approved wiring 

method. See Figure 1 for connection diagrams. 

9.  Before starting the fan, double check to ensure there 

are no obstructions that could interfere with proper 

fan operation and airflow. Verify proper fan rotation, 

resulting in air flow directed at the adjacent face of  the 

gear drive.

10.  Remove proper condensation plug. See Figure 3 

below. Do not discard. Plug is to be used during 

cleaning.

NOTES

:

AIR SUPPLY AND TEMPERATURE

 — Sufficient air supply 

over the motor must be assured in all circumstances. 

Limits of  operating ambient temperature are 14°F to 113°F 

(–10°C to 45°C).

RESTRICTION ON USE

 — Fan blade material 

is Polypropylene which is unsuitable and/or not 

recommended for certain chemicals. The following is a 

partial list of  unsuitable chemicals for guideline purposes.

Chloro-Sulphonic Acid  

Nitric Acid   Chloroform

Mixture of  HNO3-HCL  

Esters  

1:2 Trichloroethylene

Mixture of  HNO3-H2SO4  

Benzene  

Trichloroethylene

Sulfuric Acid, fuming  

Gasoline  

Diethyl Ether

Carbon Tetrachloride  

Toluene  

Chlorine, Liquid 

Chlorobenzene  

Xylene

CLEANING

 — When cleaning fan, both condensation 

holes (Figure 3, Items 1 and 2) are to be temporarily 

plugged. If  this is not done, guarantee is void. When 

cleaning electrical equipment, always use an approved 

cleaning agent.

Summary of Contents for Falk Drive One DB




























Reviews:

No comments