background image

19

REXENER PR200 WATER HEATER WARRANTY

Warranty provided by
Rex Nordic Oy (2646942–1)
Mustanlähteentie 24A,
07230 Askola, FINLAND

1. General description

Rex Nordic provides a warranty to consumers who have purchased a product imported by an importer
either directly or from a reseller. The consumer’s rights during the warranty period are determined based
on the regulations valid in the country where the warranty or warranty service claim has been presented.
This warranty is a voluntary manufacturer’s warranty providing consumers with additional rights in
addition to their rights under national consumer legislation and shall, therefore, not impact these legal
rights. The warranty shall remain valid provided that the device is operated and serviced in accordance
with the instruction manual.

Time-restricted or temporary offers are country-specific, and the related warranty claims shall not be
presented in any country other than the country or countries in which the offer is valid.

2. Warranty coverage

The importer shall provide the products it has imported with a warranty for material and manufacturing
defects in accordance with these warranty terms. The provider of the warranty shall be responsible for
ensuring that the usability and quality of the device remain normal throughout the warranty period.
Otherwise, the device has a defect.

A defect refers to an expertly assessed deviation from the normal quality of the importer’s products or
the related guidance values provided by the manufacturer, taking into account the age of the device and
the time it has been in use. For example, manufacturing and structural defects and other defects and
deficiencies impairing usability of the device during the warranty period shall be considered defects
covered by the warranty.

However, the warranty provider shall not be responsible for the defect if it puts forward a reasonable
case that the deviation in the normal quality or usability of the device is due to a reason related to the
purchaser. The reason may be, for example, handling the device contrary to the maintenance
instructions or other wrongful use of the device or neglecting the maintenance to be carried out
according to a maintenance programme and prepared by the manufacturer or a deficient
implementation thereof. The warranty limitations have been described in more detail in Section 6.
The warranty only covers Rex Nordic Oy products imported by Rex Nordic Oy and sold by an official
dealer thereof.

Only dealers authorised by Rex Nordic Oy are allowed to market and advertise the 3-year warranty.

3. Start and duration of the warranty

The warranty period begins on the day of purchase of the product. A receipt or similar certificate of the
purchase of the product must be retained and presented in warranty-related matters to confirm the

Summary of Contents for PR-200

























Reviews: