Rexel CB345E Service And Parts Manual Download | Manualshive

Page: 35 / 55

background image

Page 35 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

SECTION 14 – GEAR BOX ASSEMBLY (A55222 – 230V, A55251 – 115V)

MODELS CB345E, CB355E, CB405E, WB705E

Disassembly :-

1.

Carry out previous sections where applicable.

2.

Remove 2 off 13 tooth spur gears from electric lay shaft.

3.

Remove 2 off e-clips from electric lay shaft.

4.

Remove shaft from gear box assembly.

5.

Unplug green 3 way header from main PCB

6.

Unscrew 3 off torx head screws which connect the main PCB (via mounting blocks) to the gear
box end plate and motor support bracket

7.

Unscrew 6 off torx head screws from motor support bracket to release gearbox and motor. Snip
cable tie holding motor to support bracket.

8.

Unscrew M8 nut on capacitor and unplug connectors from capacitor. Remove capacitor.

9.

Unscrew 4 off torx head screws from gearbox end plate. Pull end plate from gear box.

10.

Unscrew 7 off torx head screws from gear box under side. Remove bottom casing.

11.

Lift gears and shafts out of upper gear box casing.

12.

Unscrew 3 off torx head screws holding motor to gear box top casing. Remove gear box top
casing.

13.

Remove e-clip from motor/pinion assembly. Remove pinion from motor shaft.

Assembly :-

Follow the following pictorial instructions.

«
...
33
34
35
36
37
...
»

Summary of Contents for CB345E
























































Reviews:

No comments

Related manuals for CB345E

Brand: Encore Pages: 28

DREAMSTITCHER 600SO

Brand: Reliable Pages: 32

Brand: Duerkopp Adler Pages: 154

Brand: Radio Shack Pages: 20

Brand: Singer Pages: 25

aerobic twisting stepper

Brand: Brookstone Pages: 14

Brand: DURKOPP ADLER Pages: 18

Brand: JUKI Pages: 39

JURASSIC PARK PRO

Brand: Stern Pinball Pages: 60

Pioneer Eclipse 225BU

Brand: Amano Pages: 26

Brand: CPI Pages: 170

Brand: Horizon Fitness Pages: 166

Brand: Beamz Pages: 8

Brand: Galaxy Pages: 2

Brand: Nilfisk-Advance Pages: 57

Brand: Nilfisk-Advance Pages: 80

Edenwood 971361

Brand: Electro Depot Pages: 36

Brand: Nacecare Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands