8
9
GB
GB
• must not be used in the immediate vicinity of flammable
materials.
• must not be set up in the immediate vicinity of pools, fountains,
ponds, or similar bodies of water.
• must not be immersed in water or other liquids.
• must not be operated with wet hands; never look directly into
the light source.
• must never be covered.
• must never be operated with an open housing, missing or
damaged wiring compartment, or missing or damaged lens.
• must never be left unattended while in operation or in the
cooling phase.
• must never be left unattended in the vicinity of children.
• must never be sprayed or cleaned using a steam pressure
cleaner since this can damage the insulation and seals.
• must never be repaired by the user. Repairs must only be
carried out by the manufacturer or an authorized service
representative.
TECHNICAL dATA
• Output:
HFGT120AST
max.
150W
HFGT400AST
max.
500W
• Voltage:
230V~, 50Hz
• Protection class:
IP44
• Replacement illuminant:
120W
- Item No. 0599940555
R7s
400W
- Item No. 0599950555
H05RN-F
ILLUMINANT INSTALLATION
• Loosen the screw on the top of the floodlight and swing the lens forward.
• Remove the illuminant from the packaging.
• Avoid touching it with bare hands since this causes grease stains which
lead to overheating. Use a clean, dry, lint-free cloth.
• Insert one end of the illuminant into the socket, press against it, and insert
the other end of the illuminant into the socket. Ensure that the socket is not
damaged.
• Then close the lens and retighten the screw.
INSTALLING THE HANdLE ANd BASE (see 1 and 2)
• Loosen the wing nut on the support and insert the base into the handle.
Insert the wing nut into the hole provided on the handle and tighten it.
SETTING THE FLOOdLIGHT dIRECTION
• Loosen the screws on the sides underneath the housing and adjust the
floodlight direction – ensure that the handle is not illuminated – and then
retighten all screws.
The floodlight is now ready for use and can be operated under the intended
conditions – it is essential that the requirements specified under “General
Safety Instructions” in regards to the installation location are followed.
REPLACING THE ILLUMINANT
You can find the technical data for the illuminant under “Technical Date” or on
the type plate attached to the floodlight housing.
• Before opening the halogen floodlight, disconnect the power cable and
allow the floodlight to cool down sufficiently!
• Loosen the screw for the lens on top of the floodlight and swing the lens
forward.
• Remove the illuminant from the packaging.
• Avoid touching it with bare hands since this causes grease stains which
lead to overheating. Use a clean, dry, lint-free cloth.
• Insert one end of the illuminant into the socket, press against it, and insert
the other end of the illuminant into the socket. Ensure that the socket is not
damaged.
• Then close the lens and retighten the screw.
CLEANING
• Before cleaning the halogen floodlight, disconnect the power cable and
allow the floodlight to cool down sufficiently.
• Clean with a dry or slightly moist, clean, lint-free cloth and a mild detergent
if required. Do not use cleaners that contain abrasives or solvents.
• If required, the illuminant can be cleaned with a lint-free cloth moistened
with ethyl alcohol. ATTENTION! After cleaning the illuminant with ethyl
alcohol, it must be allowed to air dry for at least 20 minutes.
MAINTENANCE
• Check the plug, power cable, and housing of the halogen floodlight for
damage before each use. If the lens is damaged it must be replaced
immediately.
• Clean any dirt from the housing or the lens immediately, since it could
cause overheating.
ANL_0593077555_0593079555.indd 8-9
26.07.2012 11:06:50
