9
Change of batteries:
Please change dead batteries promptly. The settings are not cleared, if the
batteries are changed within one minute. Weak batteries reduce the range a
lot.
Choice of melodies:
1. Turn the slide switch of the device to „ON”, after the insertion of the
batteries.
2. Open the transmitter on the backside. Over the plug-bridge #9 you can
choose the desired melody. Totally there are three different melodies
available.
3. To adjust the different melodies, you have to put the plug-bridge #9 in the
three different positions. Position 1-2 (Big Ben), Pos. 2-3 (two-tone) or
don‘t plug in the bridge (three-tone).
8
9
9
8
Position:
1
2
3
1
2
3
1
2
3
Melody A
Big Ben
Melody B
double ring
Melody C
3
ring
Change of code in the case of interferences:
If there are interferences with other radio-units or the chime is disturbed by
other devices, the transmitter-code must be changed:
A: Adjust a new sender-code on the sender:
1. Push the button #8 until the LED lights.
2. Push the button #8 once again within 5 seconds. The LED blinks.
Now a new code is created.
B: Inherit a new code on the receiver
1. Carry out sequence A.
2. Push button #2 on the receiver, to start the learning process.
3. Push the push-button #5 on the transmitter within 7 seconds. The LED #6
on the transmitter lights during the hitting.
4. If the learning process is successful, the LED #3 on the receiver blinks
three times and the adjusted melody is played.
Wall fastening:
Chime unit:
1. Screw the enclosed screw in the wall, until it sticks out about 5mm.
2. On the backside of the gong there‘s the lug #10.
3. Hang the chime with the lug up on the screw.
Chime unit:
1. Remove the housing cover #7.
2. Fix the housing cover with the enclosed screw on the wall.
3. Put the front of the sender on the housing cover again.
Manual Instruction
Ausstattung:
Transmission range:
approx. 50m (outdoor)
Chime function:
3 melodies for selection
Frequency: 433MHz
Battery:
3x1,5V DC type C (receiver / door chime)
1x12V DC type 23A (transmitter / push button)
Features:
Ein
Aus
3
1
4
2
10
5
6
7
9
8
#1 On/Off
On/Off-Button of the door chime
#2 SET Button
Automatic code search in the case of
interference (32000 coding combinations)
#3 LED indicator
Light on when learning code
#4 Battery Case
Required batteries: 3x1,5V DC type C
#5 Push button
Button to activate chime
#6 LED indicator
Light on, when pressing or generating new code
#7 Battery Case
Required batteries: 1x12V DC type 23A
#8 SET Code button Push to generate new code
#9 3 pin plug
3 melodies for selection
#10 hang-up lug
for wall assembl
Replace the batteries:
Chime unit:
The batteries (3 pieces, 1,5V, type C) are inserted on the backside of the chime,
after the cover #4 (push cover in the direction of the arrow) is opened. Pay
attention to the polarity, which is marked in the battery case.
Push-button:
The batteries (1 piece, 12V, type 23A) is inserted in the push-button, after the
cover #7 (the lock-in on the front of the push-button must be pushed in with
a screwdriver) is opened. Pay attention to the polarity, which is marked in the
push-button. The push-button is delivered with already inserted batteries.
ANL_468344.indd 9
13.11.2017 14:11:44
