Rethink Robotics Baxter User Manual Download

Page: 142 / 183

140

Intera 3.2

Maintaining and Supporting Baxter

To calibrate an arm:

1. Make sure there is a clear, 5-foot radius around and above the base of the robot.

If Baxter is attached to a pedestal, and it is not possible to clear the workspace
around the robot:

•

Mark the current location of Baxter by drawing on or affixing tape to the floor
near the edges or corners of the pedestal. (This action will help to re-position
Baxter after moving it for calibration.)

•

Roll Baxter on its pedestal, away from the workspace and into an area large
enough for the arms to move freely.

2. Make sure Baxter is level.

3. Scroll to Main Screen > Settings > Advanced > Calibrate Arms; then select a

form of calibration (Basic, Factory, or Spring).

4. Select one or both arms; then press OK to begin the calibration.

5. Move away from the robot, and make sure all persons are clear of Baxter.

The selected arm moves as follows for each type of calibration:

•

Basic – the arm drops to the side of the robot, then rises up and extends
outward.

•

Factory – the arm moves to the side of the robot, then rises up and extends
outward in a few different directions.

•

Spring – the arm moves to the side of the robot with the elbow at the lowest
point, then rises up and extends outward.

Summary of Contents for Baxter
























































































































































































Search results

Summary of Contents for Baxter

Reviews:

Related manuals for Baxter

Brands by name

Popular brands

Rethink Robotics Baxter, User Manual

Search results

Summary of Contents for Baxter

Reviews:

Related manuals for Baxter

Brands by name

Popular brands