background image

 

 

Environmental information

 

This device should be disposed of separately, not as unsorted municipal waste. To dispose of your 
device, you should use appropriate collection, reuse and recycling systems available in your region. 

The use of these collection, reuse and recycling systems is designed to reduce pressure on natural 
resources and prevent hazardous substances from damaging the environment. 
If you need information on these disposal systems, please contact your local waste administration. 

The crossed-bin symbol invites you to use these disposal systems. If you require information on 
collection and disposal of your ResMed device please contact your ResMed office, local distributor 

or go to www.resmed.com/environment. 

 

Servicing 

The AirCurve 10 device is intended to provide safe and reliable operation when operated in 
accordance with the instructions provided by ResMed. ResMed recommends that the AirCurve 10 

device be inspected and serviced by an authorized ResMed Service Centre if there is any sign of 
wear or concern with device function. Otherwise, service and inspection of the products generally 

should not be required during their design life. 

 

Limited warranty 

ResMed Ltd (hereafter 'ResMed') warrants that your ResMed product shall be free from defects in 
material and workmanship from the date of purchase for the period specified below. 

Product 

Warranty period 

 

Mask systems (including mask frame, cushion, headgear and tubing)—excluding 

single-use devices 

 

Accessories—excluding single-use devices 

 

Flex-type finger pulse sensors 

 

Humidifier water tubs 

90 days 

 

Batteries for use in ResMed internal and external battery systems 

6 months 

 

Clip-type finger pulse sensors 

 

CPAP and bilevel device data modules 

 

Oximeters and CPAP and bilevel device oximeter adapters 

 

Humidifier cleanable water tubs 

 

Titration control devices 

1 year 

 

CPAP, bilevel and ventilation devices (including external power supply units) 

 

Humidifiers 

 

Battery accessories   

 

Portable diagnostic/screening devices 

2 years 

This warranty is only available to the initial consumer. It is not transferable. 
If the product fails under conditions of normal use, ResMed will repair or replace, at its option, the 
defective product or any of its components.   
This Limited Warranty does not cover: a) any damage caused as a result of improper use, abuse, 
modification or alteration of the product; b) repairs carried out by any service organization that has 

not been expressly authorized by ResMed to perform such repairs; and c) any damage or 

contamination due to cigarette, pipe, cigar or other smoke. 
Warranty is void on product sold, or resold, outside the region of original purchase. 

20

 

Summary of Contents for AirCurve10 ASV
























Reviews: