background image

II 

 

 

LIMITED WARRANTY 

   

Renesas warrants its user system interface cables to be manufactured  

  in accordance with published specifications and free from defects in  
  material and/or workmanship. Renesas will repair or replace any  
  user system interface cables determined to be defective in material  
  and/or workmanship. User system interface cables are wearing parts  
  which Renesas will not repair or replace if damaged and/or worn  
  through use. The foregoing shall constitute the sole remedy for any  
  breach of Renesas's warranty. This warranty extends only to you, the  
  original Purchaser. It is not transferable to anyone who subsequently  
  purchases the user system interface cable from you. Renesas is not 
  liable for any claim made by a third party or made by you for a third 
 party. 

DISCLAIMER 

   

RENESAS MAKES NO WARRANTIES, EITHER EXPRESS OR  

  IMPLIED, ORAL OR WRITTEN, EXCEPT AS PROVIDED  
 HEREIN, INCLUDING WITHOUT LIMITATION THEREOF,  
  WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY,  
  FITNESS FOR ANY PARTICULAR PURPOSE OR USE, OR  
  AGAINST INFRINGEMENT OF ANY PATENT. IN NO EVENT  
  SHALL RENESAS BE LIABLE FOR ANY DIRECT, INCIDENTAL  
  OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR  
  LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE  
  USER SYSTEM INTERFACE CABLE, THE USE OF ANY USER  
  SYSTEM INTERFACE CABLE, OR ITS DOCUMENTATION,  
  EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.   
  EXCEPT AS EXPRESSLY STATED OTHERWISE IN THIS  
  WARRANTY, THIS USER SYSTEM INTERFACE CABLE IS SOLD  
  "AS IS ", AND YOU MUST ASSUME ALL RISK FOR THE USE  
  AND RESULTS OBTAINED FROM THE USER SYSTEM  
 INTERFACE CABLE. 

Summary of Contents for H8S/2615 Series





























Reviews: