background image

IV 

 

SAFETY PAGE 

READ FIRST 

• READ this user's manual before using this user system interface cable. 

• KEEP the user's manual handy for future reference. 

Do not attempt to use the user system interface cable until you fully understand its 
mechanism. 

DEFINITION OF SIGNAL WORDS 

 

This is the safety alert symbol.  It is used to alert you to potential personal  

 

injury hazards.  Obey all safety messages that follow this symbol to avoid  

 

possible injury or death.

 

DANGER

 

DANGER

 indicates an imminently hazardous situation which, if not  

 

avoided, will result in death or serious injury.

 

WARNING

 

WARNING

 indicates a potentially hazardous situation which, if not  

 

avoided, could result in death or serious injury. 

CAUTION

 

CAUTION

 indicates a potentially hazardous situation which, if not  

 

avoided, may result in minor or moderate injury. 

CAUTION

 

CAUTION

 used without the safety alert symbol indicates a  

 

potentially hazardous situation which, if not avoided, may result  

 

in property damage.

 

NOTE

 emphasizes essential information. 

Summary of Contents for H8S/2615 Series





























Reviews: