Renault LAGUNA 2000 Manual Download Page 9

Page: 9 / 84

LIFTING

Underbody lifts

02-4

FITTING THE SAFETY STRAPS

Fastening the vehicle with straps allows work to be
carried out beneath the vehicle free from obstruction.

The strap must be placed at the front and/or rear of the
vehicle during any operation involving the transfer of
weight.

Check the strap before each use.

The lift pads are placed under the vehicle by the tool
kit jack support.

Lift the vehicle a few centimetres.

Protect the vehicle interior (seats, etc....).

Place the strap through under the arms of the lift and
pass twice around the vehicle, placing the strap
protectors correctly so as not to damage the bodywork
or upholstery.

Do not pull too tight.

The following example shows a vehicle secured at the
front.

Summary of Contents for LAGUNA 2000





















































































Search results

Summary of Contents for LAGUNA 2000

Reviews:

Related manuals for LAGUNA 2000

Brands by name

Popular brands

Renault LAGUNA 2000, Manual

Search results

Summary of Contents for LAGUNA 2000

Reviews:

Related manuals for LAGUNA 2000

Brands by name

Popular brands