background image

Installation

Perform the installation as follows:

1.

Cut the required holes out of the mounting

template.

2.

Fasten the mounting template [1] to the wall.

Ensure that this is level [A] (for a detailed

drawing of the mounting template, see 

Fig. 11).

3.

Mark the required core holes and fastening

points shown on the mounting template on

the wall.

4.

Remove the mounting template.

5.

Using a corresponding core drill machine [2],

drill two 162 mm diameter holes for the air

supply and exhaust in the wall [3] (the pilot

hole should be 5-10 mm [3a]. In addition, a

third hole for the condensate hose should be

drilled (here the diameter should be 35 mm

[4]). Drill the holes to fix the mounting rail.

Ø 162 mm

A

1

2

Ø 35 mm

4

3

3

Ø 162 mm

Ø 5-10 mm

3a

6.

Shorten the supplied plastic pipe to the

proper length. The plastic pipe should be 70

mm shorter than the wall thickness meas-

ured.

7.

Install the shortened pipe in the wall.

8.

Now insert the supplied internal spigots as

well as the outer covers (the air flow louvres

should point towards the ground). Fasten

these with the screws supplied.

9.

If it is not possible to fasten the outer covers

to the exterior façade using the screws, use

the supplied springs to fix the outer covers to

the internal spigots.

10.

If the wall thickness is less than 10 cm, the

internal spigots must be directly screed to the

unit. Before fixing, remove the seals [5] and

place them back on the connection spigots

again after fixing pointing towards the wall.

 

 

 

 

 

15

Summary of Contents for KWT 200 DC





































Reviews: