background image

Type of task 

 

Checks / Maintenance / Inspection

Commissioning

Monthly

Half-yearly

Yearly

General

Medium cycle bleeding

Check medium filling

Contamination of fin register

Filter contamination

Check voltage and current

Check function of fan

Check condensate drainage

Check insulation

Care and maintenance

Regular care and maintenance 
ensure the trouble-free operation 
and long service life of the unit.

Care and maintenance work may 
only be carried out if the unit is 
disconnected from electrical power.

      CAUTION

Care

■ 

Ensure the unit is protected 
against dirt, mould and other 
deposits.

■ 

Clean the unit using a damp 
cloth. Do not use any caustic, 
abrasive or solvent-based 
cleaning products. Do not use 
a jet of water.

■ 

Clean the fins on the unit prior 
to long shutdown periods.

Maintenance

■ 

We recommend that you take 
out a maintenance contract 
with an annual service from 
an appropriate specialist firm.

Cleaning the housing

1.  Disconnect the power supply 

to the unit.

2.  Clean the grill and cover with 

a soft, damp cloth.

3.  Switch the power supply 

back on.

Air filter for indoor unit

Clean the air filter at intervals 
of no more than 2 weeks. 
Reduce this interval if the air 
is especially dirty.

A maintenance contract will 
guarantee that your system 
always operates reliably!

      TIP

3.  Fold the filter downwards and 

pull it out towards the front. 

4.  Clean the filter with 

a commercially available 
vacuum cleaner. To do this, 
turn the dirty side upwards 

(Figure 1)

.

5.  Dirt can also be removed 

by carefully cleaning with 
lukewarm water and mild 
cleaning agents. Turn the dirty 
side downwards to do this 

(Figure 2)

.

6.  If water is used, let the filter 

dry out properly in the air 
before fitting it back into 
the unit.

7.  Carefully insert the filter. Ensure 

that it locates correctly.

8.  Switch the power supply 

and the unit back on.

Cleaning the filter

1.  Disconnect the power supply 

to the unit.

2.  If necessary remove the unit's 

cover. 

 

Follow the chapter "Removal 
of the unit's cover".

 

 

Cleaning using a vacuum cleaner

 

 

Cleaning with lukewarm water

Filter removal

REMKO KWK / KWK-ZW

8

Summary of Contents for KWK 130

































Reviews: