background image

Ventilation

Only the supply air fan operates in this setting.

Thermostatic regulation and heating operation are

not possible in this operating mode.

Switch the operating switch to the corresponding

position 1.

Fig. 4: Ventilation switch position

Heating with room thermostat (accessory)

The units operate fully automatically and according

to the room temperature.

1.

Pull out the strapping plug [2].

2.

Connect the room thermostat [4] plug [3] with

the thermostat receptacle [1] on the unit.

3

1

3.

Place the room thermostat [4] at a suitable

location in the room. The thermostat sensor

must not be located directly in the warm air

flow and must not be placed directly on a

cold floor.

4.

Set the desired temperature on the room

thermostat [4].

4

5.

Select the desired power position on the

operating switch.

Shutdown

1.

Switch the operating switch to the "0" (off)

position.

The supply air fan runs on to cool the units

and only switches off after the cooling down

phase is complete. The fan can switch on

and run several times before the final shut-

down.

2.

If shut down for an extended period, discon-

nect the units from the mains power supply.

 NOTICE!

Never interrupt the mains connection prior to

the completion of the follow-up cooling phase.

There is no warranty claim for damage to the

units from overheating.

 

 

 

 

 

11

Summary of Contents for ELT 40





















Reviews: