11
Cleaning & Maintenance
10
To assure smooth, efficient perfor-
mance, it is important to clean your
shaver. The hand-held unit shall be
detached from the power supply cord
before cleaning. The shaver shall not
be used until it has dried.
The shaver is a
washable shaver,
the hand-held
part of which may
be cleaned under
water.
Daily
Brush inside the head assembly after
each use:
1.
Turn the shaver
off.
2.
Grip the head
assembly by
the three ridges
and pull it off
the shaver.
3.
Use the
cleaning brush
to sweep out
the internal
part of the
head assembly
and the hair
pocket area,
where 3 shaver
spindles are
located.
4.
Replace head
assembly.
Weekly
Clean under the cutter assembly at
least once a week:
1.
Turn the shaver off.
2.
Open the head assembly as above.
3.
Unscrew the center screw knob
to remove the cutter retainer
assembly.
4.
Use the cleaning brush to sweep
the dust and hairs from under the
cutters.
5.
Replace head assembly.
Lubricate
Remington
®
Shaver Saver
®
Lubricant
(SP-4) lubricates and cleans your
shaver's cutters and head assembly.
The lubricant helps remove hair clip-
pings while reducing wear. A quick
spray after each shave keeps your
shaver operating at peak performance.
Cleaning Cautions
■
The construction of this shaver
is for dry operation only. It is not
waterproof. Never put the shaver
in part or completely into water.
■
Never clean the shaver or replace
the cutters while it is plugged into
an electrical outlet.
■
Do not use an aggressive cleansing
agent as this may destroy the
shaver coatings.
■
Do not clean or remove the head
assembly while the shaver is
When is it Time to Replace
Your Heads and Cutters?
It is very important to replace your
heads and cutters when necessary
to ensure a close, comfortable shave
without irritation. We recommend
they be replaced every 12 months.
Here are some signs of head and
cutter wear, indicating that replace-
ment is needed.
Irritation
As the heads get excessively worn
you may experience some skin
irritation. This would be especially
noticeable when you apply after-
shave lotion.
Pulling
When the cutters wear you may
feel a sense of pulling and a loss of
closeness when you shave. This is
an indication that it is time to replace
your heads and cutters.
The replacement part for this shaver
is model #SP-29.
U.S. residents:
To order, contact us
at 800-736-4648, visit us at
www.remington-products.com
or
visit your local retailer.
Canadian residents:
For any shaver
accessory requirements, please call
800-268-0425 or write: Spectrum
Brands Canada, Inc., Mississauga,
ON L4W 2T7.
Head/frame
assembly
Floating
cutter
heads
Locating pins
Cutter retainer
assembly
Center
screw
knob
Locating holes
! Important:
Make sure to align
the two locating holes in the Cutter
Retainer assembly with the pins
in the Head Frame Assembly. (See
illustration below). Then tighten
center screw knob to lock the cutters
into place.Replace head assembly on
the shaver simply by pushing it onto
the shaver. Cover shaver head with
plastic headguard between uses.
When removing the headguard or
placing it back onto the shaver, do
not apply pressure to floating cutter
surfaces, as you may damage them.
running or plugged in, as it may
cause damage to the unit's heads
or cutters.
■
Replace worn or damaged parts
with Remington
®
replacement
parts only.
34159_R450S-650S_IB_update.indd 10-11
5/24/07 11:05:12 AM
