• The Facial Attachment is only intended for use on female facial hair below the cheekbone (Fig. 10).
• DO NOT use on male beards or facial hair as the results may be permanent or uneven which may
produce changes in facial hair characteristics which may not be desirable.
TREATMENT TIPS
,
Body Treatment
•
necessary to suppress hair growth. It also ensures that you get the maximum use of the Bulb.
• For the most
results, always use the highest intensity level that does not cause discomfort on
the skin. The level you use should feel warm on your skin, but should never cause discomfort.
• You may notice that bony areas, such as elbows, shins and ankles, are more sensitive during
treatment.
• This is normal and should not be cause for alarm. To avoid this sensitivity, try stretching the skin away
from the bony area during treatment.
,
Facial Treatment
•
Test on a Patch of Skin – since facial skin tends to be more sensitive, make sure you test on a small
patch before proceeding. See section ‘Test the i-LIGHT® on your skin’ for more details.
• Use a Mirror to Guide your Treatments – using a mirror for a good view of the area to be treated and to
• Stretch Skin for Better Skin Contact – the contours of the skin may make it
for the skin contact
your teeth or use your tongue to stretch your cheeks for better skin contact.
POST-TREATMENT CARE
After treatment, you may experience slight redness or a warm sensation on your skin. This is normal and
will disappear quickly. To avoid irritation to your skin after a treatment, take the following precautions:
• Avoid sun exposure for 24 hours after a treatment. Protect the skin with SPF 30 for 2 weeks after each
treatment.
• Do not prolong sun exposure such as sunbathing, using a tanning bed, or self-tan for at least 2 weeks
after the last treatment.
• After treatment, keep the area clean and dry and drink plenty of water to keep skin hydrated.
• Do not take hot baths, showers, or use steam rooms and saunas for 24 hours after treatment.
• Do not take part in contact sports for 24 hours after treatment.
• Do not depilate (waxing, plucking, threading or creams) during the treatment – shaving is acceptable
as long as you avoid shaving 24 hours after each treatment.
• Do not use bleaching creams or perfumed products for 24 hours after treatment.
INFINITY BULB
•
• The bulb in this device is guaranteed to last for the entire warranty period as
communicated on the warranty details at the rear of this manual.
• In the extremely unlikely event that your bulb becomes empty, please contact your
local Remington Service centre who will provide you with a replacement.
,
Signs that the bulb needs replacing:
• Bulb Status Indicator is illuminated yellow: 150 Flashes remain in the bulb
• Bulb status indicator is
yellow: Bulb is empty.
CLEANING YOUR i-LIGHT® DEVICE
CAUTION:
Before cleaning your i-LIGHT®, make sure that the device is switched OFF and the power
cord is disconnected from the device.
• Regular cleaning helps to ensure optimal results and a long life for the i-LIGHT® device.
• To clean the Flash Window, use only the lint-free cloth included with your i-LIGHT® device. Take care
• For stubborn stains on the
window, dampen a cotton swab with surgical spirit or rubbing alcohol,
Use a small hand-held vacuum to remove dust and debris from the hand piece vents.
glass or the metallic surface inside the Treatment Head.
CAUTION: The i-LIGHT® is a high voltage device. Never immerse in water. Never clean the unit or any of
its parts under a tap or in a dishwasher.
,
Storage
• Switch the unit, unplug and allow to cool for 10 minutes before storage.
• Store the unit in a dry place at a temperature between 15º C and 35º C
TROUBLESHOOTING
•
Always read these instructions fully before using i-LIGHT®
• Refer to this troubleshooting guide if you experience any problems with i-LIGHT®, as this section
addresses the most common problems you could encounter with i-LIGHT®. If you have followed the
instructions in this section and continue to experience problems, please contact the Remington®
Service Centre for further assistance.
,
The power switch is ON, but the unit is not working.
• Make sure the unit is plugged into a working electrical outlet.
• Try switching to a different outlet.
IN
FINITY
16
