RELM RP7200 Owner'S Manual Download Page 14

19

20

system in the personal template. If the received MDC code is 
same as the one set in the system, it can decode successfully.
After the radio received the correct MDC signaling, according to 
the 

Receive squelch mode

set by the user, the squelch will 

be ON. Then, the radio can receive the call and the orange LED 
light flashes.

2) MDC encode
If the PTT ID of the chosen channel is set as MDC, the MDC code 
will be transmitted when calling.

The radio cannot 
be switched on or 
no display after 
switched on.

The battery

 

 

power consume

 

 

quickly after

 

 

charging.

Cannot talk to or 
hear others  in 
your group.

Other voices from 

NO.    PROBLEM            

SOLUTION

TROUBLE SHOOTING GUIDE

1

2

3

5

4

Battery pack may not be installed properly. 
Remove the battery pack and install it again.
Battery power may be insufficient. Recharge 
or replace the battery pack.

The battery life is finished; please replace it 
with a new battery pack.

 

   

 

 

 

 

The frequency or QT/DQT Signallings are not

 

 

 

 

identical and please reprogram it.

 

 

 

 

 

   

 

Make sure the SP un-mute setting of the

 

  

   

 

   

selective Signalling 5-Tone in user solution is

 

proper.

   

 

 

Out of the communication range.

Change the QT/DQT tone, and make sure 

change the tone on all radios in your group.
Please set  5-Tone selective Signalling on the 
channel.

Make sure the antenna is well connected.
Make sure the antenna is the original one.
Check if the battery power is in the normal state.
Ask your local dealer to adjust the squelch level.
Make sure the PTT button has been pressed 
completely.
Battery power may be insufficient. Recharge or 
replace the battery pack.
Transmitting frequency has not been set on the 
channel or the radio has been remote killed.
Battery power may be insufficient. Recharge or 
replace the battery pack.
Out of the communication range.

non-group 
members are 
heard on the 
channel.
Communicati
on range is 
too short.

Unable to 
transmit.

Noise is too 
loud.

6

7

 

 

MAJOR SPECIFICATIONS

RP7200

Frequency Range  

(MHz)

RF Power 

Spurious and Harmonics

Frequency Stability

Maximum Frequency deviation

(1) 136~174               (2) 400~470

                                    

                                   (3) 450~520

                                   (4) 350~400

5W (H) / 1W(L)           4W (H) / 1W(L) 

-70 dB

2.5ppm

5kHz (W)/ 

3.5kHz (M)/ 

2.2 kHz (N) 

±

±

±

±

Summary of Contents for RP7200


















Reviews: