RELM RP7200 Owner'S Manual Download Page 13

17

18

The dealer can set DTMF Signalling into encoding sequence. If 
DTMF is set in the encoding template, press the corresponding 
programmable button 

Call 1

 , 

Call 2

Call 3

, or 

Call 

4

 transmit the coding.

5-Tone Signalling

The dealer can activate or inactivate this function by 
programming.
5-Tone has 9 encoding formats: CCIR1, CCIR2, ZVEI1, ZVEI2, 
SVEI3, EEA, EIA, USER DEFINED 1, and USER DEFINED 2. 
The last tow formats are user defined. 

1) 5-Tone Decoding 
The decoding template is 5-tone decoding. Received tone 
telegram matches the decoding template, decoding succeeds. 
When receiving proper 5-tone Signalling, squelch will be activated 
according to the 

RX Squelch Mode

defined by the user. You 

can receive the call and LED flashes orange.
After the radio decoding succeeds, the radio will work according to 
the decoding call response set by the dealer. 

2) 5-Tone Encoding
Encoding template consists of at least one and at most three 
encoding sequences, and each decoding sequence can be set 
with 5-Tone, and DTMF. If it is set with 5-Tone, you need to 
program its content.
If the PTT ID on the channel you select has been set with 5-Tone, 
5-Tone Signalling will be transmitted when making a call.
Or transmit 5-Tone signal by pressing the Call 1/2/3/4 button,, 
which can be set by the dealer.

      This function can be enabled or disabled by dealers through 
      programming software.
      2Tone has 4 systems; the single tone continuous time, such as first 
      tone or second tone, could be set by the dealer.
 
      1) 2Tone decode 
      If the received 2 tone is same as the template chosen then it can 
      decode successfully.
      After the radio received the correct 2 tone signaling, according to 
      the ¡Receive squelch mode¡ set by the user, the squelch will be
      ON. Then, the radio can receive the call and the orange LED light 
      flashes.
      After decoding successfully, the radio can work according to the 
      decode call response set by the dealer.

      2) 2Tone encode

The encoding template is set in the 2 tone call list. The details 
must be set if encoding is ON.
The radio transmits the 2 tone signaling when the programmed 
call button is pressed. (The side button could be programmed as

¡Call1/2/3/4¡). This function is programmed by the dealer.

     2TONE Signalling

MDC Signaling

This function can be enabled or disabled by the dealers through 
programming software.
MDC has 4 systems, in which different main ID, group ID, etc. 
could be set by the dealer.

1) MDC decode
The option MDC system can be set through the RX signaling 

Summary of Contents for RP7200


















Reviews: