RELM RP7200 Owner'S Manual Download Page 11

13

14

   

VOX (Voice Operated Transmission)

    VOX allows hands-free transmission on the radio when using the      
    appropriate earphone/headset.
    Two types of VOX are available: built-in and external.
    If VOX has been set, when speaking voice reach the preset                    
    volume, VOX will activate the radio to transmit automatically. 

Wired Cloning Mode 

    To enter the clone mode, wired cloning function should be set on                                  
    both host and sub radio.
    Wired cloning procedures are as follows:
    1) Press and hold the Side Button 1 and 2 on the host radio while             
    turning on the radio; about 2 seconds later, orange indicator flashes    

GPS

:

GPS Position Annunciation (Optional)

  

The radio can annunciate the information of the current position 

                                          

  

such as longitude and latitude through the microphone when the 

                    

  

programmed key 

GPS Position Annunciation

is pressed. (If the 

    

  

radio cannot locate its position, then it will annunciate 

un-

        

  

positioned

). 

  

GPS ID

GPS ID Annunciation (Optional)

  

The radio can annunciate the ID number through the microphone 

        

  

when the programmed key 

GPS ID Annunciation

is pressed. 

  

GPS

GPS Time Annunciation (Optional)

The radio can annunciate the current time when the programmed 

    key 

GPS Time Annunciation

 is pressed. (The time zone can be 

set by the dealer; if the radio cannot discover the position, then it 

    will annunciate 

un-positioned

.

     

      

 

     

      

 

    twice and the radio enters cloning mode. 
2) Press once the PTT button on the host radio, and then the sub 
radio to receive data will enter Wired Cloning Mode. 
3) In the cloning mode, the host radio lights red indicator and the 
sub radio lights green indicator. 

Note:

 

During the course of cloning, if the radio models or software 
versions doesn't match, the host radio flashes red indicator (0.25s 
On 0.25s Off), and the sub radio restart; if no data is transferred, 
the host radio flashes red indicator (0.25s On 0.25s Off), and the 
sub radio restart.

TOT (Time-out Timer) 

1) TOT (Time-out Timer)
A) Time-out timer is to prevent any caller from occupying one 
certain channel and radio transmitting overlong.
b) You can program the time-out timer, i.e. the time the radio can 
transmit continuously. If the radio has been transmitting 
continuously longer than the preset time, the radio will stop 
transmitting and warning tone sounds, and please release the PTT 
button.

2) TOT Re-key
a) TOT re-key specifies the time when transmission is prohibited 
after the time-out timer is activated.
b) During the time of transmitting prohibition, if you press the PTT 
button, warning tone sounds and transmitting is prohibited.

3) TOT Pre-alert 

RADIO SETTING 

Summary of Contents for RP7200


















Reviews: