Rekluse CoreManual Installation & User Manual Download Page 8 | Manualshive

Page: 8 / 16

background image

Pg. 8

Doc ID: 191-7008001A

Doc Rev: 080720

11. Remove the center hub from the clutch basket while leaving

the thrust washer on the main shaft.

Note:

Check that the OE thrust washer is still on the main shaft

and not stuck to the bottom of the center hub assembly. The
thrust washer must be installed or clutch performance issues will
result.

Thrust

washer

«
...
6
7
8
9
10
...
»

Summary of Contents for CoreManual

















Reviews:

No comments

Related manuals for CoreManual

Brand: Banner Pages: 12

Brand: Valore Pages: 5

Brand: Lastolite Pages: 3

Brand: Paradox Pages: 2

Brand: Öhlins Pages: 8

Brand: 3SIXT Pages: 12

Sterling ALL-TERRAIN 576

Brand: Roadmaster Pages: 12

Brand: Cerlic Pages: 20

Brand: Eiko Pages: 21

Brand: SRAM Pages: 33

Brand: SimpliPhi Pages: 15

Brand: inventum Pages: 32

Classic Studex Mk2 G1326 G1326

Brand: Gitzo Pages: 1

Brand: Summer Pages: 18

Brand: Ryobi Pages: 8

Brand: Berlebach Pages: 2

Brand: Moza Pages: 57

Brand: Nauticam Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands