background image

2

Warnings and Cautions

Caution:

 In order to insure that correct operation of the Mark III instrument is maintained, any 

repair or service must be performed by experienced personnel that are trained by Reichert Inc.

Caution ESDS:

 The internal circuitry of the Mark III contains electrostatic discharge sensi-

tive devices (ESDS). Such components may be sensitive to high voltages produced by static 

discharge.

Caution:

 Do not use strong solvents or strong cleaning solutions on any part of the Mark III or 

damage to the unit may occur. 

Warning:

 Do not remove or defeat the earth ground connection on the Mark III power input 

connector or the unit’s power cord. Damage to the Mark III instrument and/or injury to the op-

erator may occur.

Warning:

 The Mark III should be used in strict accordance with the instructions outlined in this 

users guide. The safety of the operator and the performance of the instrument cannot be guar-

anteed if used in a manner not specified by Reichert Inc. 

SN

[REF]

Symbol Information

 

The following symbols appear on the instrument.

 

 

CAUTION: Risk of Electrical Shock

 

 

CAUTION: Indicates that important operating and maintenance instructions are  

 

 

included in this user guide

 

 

CAUTION: Replace with the same type and rating fuse

 

 

Date of Manufacture

 

 

Waste of Electrical and Electronic Equipment

 

 

Serial Number

 

 

Catalog Number

 

 

Ground

 

 

On - Off

 

 

Conformity with mandatory European safety requirements

Summary of Contents for ABBE MARK III



















Reviews: