background image

1. Introduction

CSE SOL G SRS1 T-E Solar Pump Station is fitted with a solar pump of the latest generation that 

permits flow control either internally by selecting a suitable mode or externally through PWM signal. 

The complicated setting of the right flow rate is not needed when the PWM signal is used, the pump 

station keeps adjusting it automatically, depending on the actual solar radiation. This means that the 

solar thermal system always works with the maximum possible efficiency.
Thanks to a direct connection of the heating element into the special socket in the pump station, 

a long power cable for the pump station and a cable ready to connect to a solar sensor, the installa-

tion is easy and fast, no qualified electrician is needed.

2. Pump Station Description

Main Features

Použití

This solar pump station contains all components necessary for current and 

efficient operation incl. complete electrical wiring. It is necessary to connect 

only the collector temperature sensor.
An electric heating element of up to 3 kW output can be connected to the 

pump station. The pump station is equipped with a special socket for this 

purpose.
No heating element is included in supply.

Popis

The pump station consist of a UPM3 Hybrid 25-70 pump, SRS1 T controller, 

check and safety valves, 2 ball valves, pressure gauge, thermometer, el. wiring, 

insulation and installation kit.
The pump station further involves: 
● connection point for an expansion vessel
● safety valve outlet, incl. extension piping terminating under the pump station  

    for easier connection
● ball valves for filling, draining and topping up a solar thermal system
● special socket to connect a heating element of max. output of 3 KW / 230V
●  two connected temperature sensors for solar consumer (4m cable)
● solar temperature sensor (2m cable, silicone insulation)
● 230V power cable w. el. plug (3m cable, PVC insulation)

Installation

on a tank or wall

Working fluid

water-glycol mixture (max. 1:1)

Codes corresponding to connection sizes

Connection

G 3/4“ M

G 1“ M

Flow measurement range

2-12 l/min

8-28 l/min

Code

18970

18962

Summary of Contents for CSE SOL G SRS1 T-E













Reviews: