background image

6

ENGLISH

the power to this Regent light fixture. By inadvertently turning off the power, the
mode of operation may be changed. If the mode of operation needs to be
changed, just flip up the light cover to find a helpful guide at your fingertips with
quick and easy instructions which will allow you to select the mode of your
choice.

NOTE: The modes of operation ONLY apply to this Regent motion

lantern.

Step 1: Turn off the power at the main fuse/breaker box.
Step 2: Locate the inside light switch that will control your Regent motion 

activated lantern.

Step 3: If you have a single light switch, remove the two screws that are holding

your current cover in place.

NOTE: DO

NOT REMOVE THE COVER. The
Regent light switch cover is designed to
fit over your existing cover!  If you have
a bank of light switches (several switch-
es together), locate the one switch that
will control your Regent fixture.
Remove the two screws, one directly
above and one directly below the
switch.

Step 4: Open the lid on your Regent light switch cover. Align the holes on the

Regent light switch cover over the holes in your current cover. Re-insert
the screws to secure it in place.

NOTE: If your screws are not long

enough, it may be necessary for you to replace them with longer screws
to secure the Regent light switch cover over your existing cover (P).

Step 5: Turn on the power at the main fuse/breaker box.
Step 6: Turn the light switch to the “ON” position and close the lid on your light

switch cover.

How to select your desired feature

(continued)

Mode of 

operation:

Set slide switch 

on sensor to:

How to set

power switch:

Test Setting

Lantern should turn on with

motion both day and night.

Lantern should turn OFF

after 4 secs.

TEST

Keep the power to 

the fixture on.

Motion Activated 

(auto setting)

Lantern should turn on with

motion only at night and should

turn off after 4 or 12 min.

of no motion.

AUTO 4 MIN

or

AUTO 12 MIN

Keep the power to 

the fixture on.

2 Hour 

NIGHT TIME ON  then 

Motion Activated

Lantern should turn on 

automatically at night 100%
brightness for 2 hours, then
reset to regular auto motion 

setting for the remainder 

of the evening.

NIGHT TIME ON

2 HR

(2 Hours)

Note: Once the lantern has

come on in the selected “Night

Time On” mode, you cannot

change the mode setting until

the next dawn. The lantern will

operate in the first “Night Time

On” mode selected 

(2 hour, 4 hour, or 6 hour),

even if changed.

Keep the power to the 

fixture on.

P

Do not remove your
current cover.

Place over
existing
cover.

Summary of Contents for CMDL Series





























Reviews: