manualshive.com logo in svg

Regency U1500E-LP11, Manual

Share
Download
Regency U1500E-LP11 Manual Download Page 8

8    |  U1500E-11 Gas Fireplace

U1500E-11 Gas Fireplace

Optional Framing Kit

919-807

08.21.17

OPTIONAL FRAMING KIT

1.  Construct the timber framing, ensure inside dimensions are 48-5/8" H x 

55" W as shown below.

55"

48-5/8""

2.  Bend both side nailing strips from the side of the appliance until 

positioned as shown below.

     Determine the overall combined thickness of the non-combustible board 

+ finished material being used. The nailing strips can be adjusted up to 
1-1/2" .

   Remove top nailing strip (by removing 3 screws) and recycle.

Nailing Strips

Remove Top

Nailing Strip

3.  Adjust the nailing strips by loosening 2 screws on each nailing strip - 

adjust and retighten screws.

4.  Attach both vertical studs (676-036)A to the vertical timber studs and 

secure using 6 screws (2 at bottom, 2 at top and 2 on sides) as shown. 

NOTE: Ensure the flat side of the steel stud is facing the wood framing.

(676-036)A

Flat side out

5.  Secure horizontal steel header stud 

(606-067) 

with 2 screws per side as 

per diagram.

6.  Slide the unit into position. Hook up gas, venting, electrical and 

conversion kit (if purchased) prior to installing the remaining steel studs.

7.  Secure the upper horizontal steel studs as shown with 2 screws per 

side.

8.  Secure the 2 remaining large horizontal studs 

(606-066)A

 with 2 screws 

per side as shown.

Large stud

 (606-066)A

Large stud 

(606-066)A

Header stud

(606-067)A

Horizontal 

stud

(606-067)A

7 03 A

A

A

1

U1500E

Summary of Contents for U1500E-LP11












Reviews:

No comments

Brands by name

Popular brands

Load more brands