background image

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.  6988 Venture St., Delta, BC  Canada, V4G 1H4

919-065d

10/03/14

Owners & 

Installation Manual

Installer: Please complete the details on the back cover 

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

MODELS: PTO30CFT

                PTO30IST

                  PTO30CKT

WARNING: FOR OUTDOOR USE ONLY

 

www.regency-fi re.com

    WARNING:  
If the information in these instructions 
are not followed exactly, a fire 
or explosion may result causing 
property damage, personal injury or 
loss of life.

    WARNING - FOR YOUR SAFETY
What to do if you smell gas:
•Shut off gas to the appliance.
•Do not try to light any appliance.
•Extinguish any open fl ame.
•If odor continues, keep away from the appliance and im-

mediately call your gas supplier or fi re department.

•Do not touch any electrical switch: do not use any phone 

in your building.

•Immediately call your gas supplier from a neighbour's 

phone. 

•Follow the gas supplier's instructions.
•If you cannot reach your gas supplier, call the fi re 

department.  

    WARNING:  
Improper installation, adjustment, 
alteration, service or maintenance 
can cause injury or property damage.  
Read the installation, operating and 
maintenance instructions thoroughly 
before installing or servicing this 
equipment.

Installation and service must be 
performed by a authorised installer, 
service agency or the gas supplier,
in accordance with this manual.

     WARNING:  
Do not store or use gasoline or other fl ammable vapours 
and liquids in the vicinity of this or any other appliance. 
A LP-cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.

LISTINGS AND CODE APPROVALS

These gas appliances have been tested 
in accordance with  AS4565 / AS4558 
and have been certifi ed by the IAMPO 
Oceana for installation and operation 
as described in these Installation and 
Operating Instructions.

Your unit should be serviced annually 
by an authorised service person.

Regency Plateau

®

 Series 

Outdoor Decorative Gas Appliances

Summary of Contents for Plateau PTO30CFT





































Reviews: